HFSS时域仿真设置

步骤 1: (‎2017/‎5/‎24 14:54:24) 用户在"HFSS (菜单项目)"上左键单击(在"ANSYS Electronics Desktop - Project2 - HFSSDesign1 - 3D Modeler - [Project2 - HFSSDesign1 - Modeler]"中)

步骤 2: (‎2017/‎5/‎24 14:54:25) 用户在"Solution Type... (菜单项目)"上左键单击

步骤 3: (‎2017/‎5/‎24 14:54:26) 用户在"Transient (单选按钮)"上左键单击(在"Solution Type: Project2 - HFSSDesign1"中)

步骤 4: (‎2017/‎5/‎24 14:54:28) 用户在"OK (按钮)"上左键单击(在"Solution Type: Project2 - HFSSDesign1"中)

步骤 5: (‎2017/‎5/‎24 14:54:31) 用户在"Project2 - HFSSDesign1 - Modeler (窗口)"上右键单击(在"ANSYS Electronics Desktop - Project2 - HFSSDesign1 - 3D Modeler - [Project2 - HFSSDesign1 - Modeler]"中)

步骤 6: (‎2017/‎5/‎24 14:54:35) 用户在"Voltage... (菜单项目)"上左键单击

步骤 7: (‎2017/‎5/‎24 14:54:37) 用户在"打开 (按钮)"上左键单击(在"Voltage Source : General"中)

步骤 8: (‎2017/‎5/‎24 14:54:38) 用户在"New Line... (列表项目)"上左键单击

步骤 9: (‎2017/‎5/‎24 14:54:39) 用户在"Project2 - HFSSDesign1 - Modeler (窗口)"上左键单击(在"ANSYS Electronics Desktop - Project2 - HFSSDesign1 - 3D Modeler - [Project2 - HFSSDesign1 - Modeler]"中)

步骤 10: (‎2017/‎5/‎24 14:54:40) 用户在"Project2 - HFSSDesign1 - Modeler (窗口)"上左键单击(在"ANSYS Electronics Desktop - Project2 - HFSSDesign1 - 3D Modeler - [Project2 - HFSSDesign1 - Modeler]"中)

步骤 11: (‎2017/‎5/‎24 14:54:42) 用户在"下一步(N) > (按钮)"上左键单击(在"Voltage Source : General"中)

步骤 12: (‎2017/‎5/‎24 14:54:43) 用户在"Active (单选按钮)"上左键单击(在"Voltage Source : Transient"中)

步骤 13: (‎2017/‎5/‎24 14:54:44) 用户在"完成 (按钮)"上左键单击(在"Voltage Source : Transient"中)

步骤 14: (‎2017/‎5/‎24 14:54:46) 用户在"HFSSDesign1 (Transient Network)* (树项目)"上左键单击(在"ANSYS Electronics Desktop - Project2 - HFSSDesign1 - 3D Modeler - [Project2 - HFSSDesign1 - Modeler]"中)

步骤 15: (‎2017/‎5/‎24 14:54:48) 用户在"Analysis (树项目)"上右键单击(在"ANSYS Electronics Desktop - Project2 - HFSSDesign1 - 3D Modeler - [Project2 - HFSSDesign1 - Modeler]"中)

步骤 16: (‎2017/‎5/‎24 14:54:50) 用户在"Add Solution Setup... (菜单项目)"上左键单击

步骤 17: (‎2017/‎5/‎24 14:54:53) 用户在"Input Signal (选项卡项目)"上左键单击(在"Transient Solution Setup"中)

步骤 18: (‎2017/‎5/‎24 14:54:55) 用户在"打开 (按钮)"上左键单击(在"Transient Solution Setup"中)

步骤 19: (‎2017/‎5/‎24 14:54:56) 用户在"Hz (列表项目)"上左键单击

步骤 20: (‎2017/‎5/‎24 14:54:57) 用户在"Min Freq: (编辑)"上鼠标拖动开始(在"Transient Solution Setup"中)

步骤 21: (‎2017/‎5/‎24 14:54:57) 用户在"Profile (组)"上鼠标拖动结束(在"Transient Solution Setup"中)

步骤 22: (‎2017/‎5/‎24 14:54:58) 用户在"Min Freq: (编辑)"上键盘输入(在"Transient Solution Setup"中) [...]

步骤 23: (‎2017/‎5/‎24 14:54:59) 用户在"Max Freq: (编辑)"上鼠标拖动开始(在"Transient Solution Setup"中)

步骤 24: (‎2017/‎5/‎24 14:55:00) 用户在"Profile (组)"上鼠标拖动结束(在"Transient Solution Setup"中)

步骤 25: (‎2017/‎5/‎24 14:55:15) 用户在"打开 (按钮)"上左键单击(在"Transient Solution Setup"中)

步骤 26: (‎2017/‎5/‎24 14:55:16) 用户在"kHz (列表项目)"上左键单击

步骤 27: (‎2017/‎5/‎24 14:55:22) 用户在"确定 (按钮)"上左键单击(在"Transient Solution Setup"中)