这篇文章介绍一下DLC1.3工况以及在bladed中怎么设置。
DLC1.3工况是极限工况,从工况表中可以看出1.3工况的轮毂处极端流风的平均风速是在切入和切出风速之间,波浪是正常海况,风和波浪的方向是同向且是单向的,海流是正常流,水位是平均海平面。
If the extreme design values of the blade root moments derived from DLC1.1 are not exceeded by the extreme design values derived for DLC1.3, the factor c for the extreme turbulence model used in DLC1.3 (see IEC 61400-1) may be increased until the extreme design values of the blade root moments computed in DLC1.3 are equal to or exceed the relevant extremes. The characteristic values of the loads relevant for other turbine components may be determined from this analysis based on DLC1.3 with the increased c value. As an alternative to this analysis, the appropriate characteristic values of all load components relevant for each specific turbine component may be directly determined or extrapolated from the simulation.
DLC1.3 embodies the requirements for ultimate loading resulting from extreme turbulence conditions. Normal sea state conditions (NSS) shall be assumed for this design load case. The significant wave height for each individual sea state shall be taken as the expected value of the significant wave height conditioned on the relevant mean wind speed.
如果DLC1.3的极限设计值未超出DLC1.1计算所得的叶根弯矩的极限设计值,可增加DLC1.3极端湍流模型所用到的参数c值(参照IEC 61400-1),直到DLC1.3计算的叶根弯矩等于或者超过相关极值。风力发电机组其他部件相关载荷的特征值可基于增加c值的DLC1.3来分析确定。作为分析的替代方案,风力发电机组各个特定部件相关的所有载荷的特征值可直接通过仿真结果确定或由外推得到。
DLC1.3包含了极端湍流条件引起的极限载荷要求。DLC1.3应采用正常海况(NSS),且每个单独海况的有义波高应取为相应平均风速条件下有义波高的期望值。
以上是IEC标准对DLC1.3工况的介绍,接下来介绍一下外推方法。
使用DLC1.1工况外推出叶根Mx,My,Dx50年一遇极端载荷。
计算DLC1.3工况叶根Mx,My,Dx 的特征载荷。
如果DLC1.3工况叶根Mx,My,Dx 的特征载荷小于DLC1.1工况外推的结果,这时就修改ETM湍流度系数c,确保DLC1.3特征载荷大于DLC1.1外推出的50年一遇极端载荷。
使用DLC1.3的所有特征载荷作为该风电机组50年一遇的极端载荷,也就是说抛弃了DLC1.1。
DLC1.1工况只是外推出叶根Mx,My,Dx50年一遇极端载荷,作为一个过程计算。
接下来就讲讲DLC1.3工况怎么在bladed中计算。
首先是风的设置,切入和切出风速以3米每秒和25米每秒举例,步长取2米每秒。偏航误差取-8、0、和8三个方向,每个方向取两个不同的风种子,每个风速取六个(也可以分割方向就六个)。
以5米每秒的平均风速为例,极端流风三个方向的湍流强度bladed不能自动生成需要根据IEC标准手工计算,但批处理时却可以自动生成,Wind direction 填写偏航误差。
波浪对应不同的风速取不同的有义波高和谱峰周期,波浪和海流的方向和风的方向是相同的。
下图举了1.3工况平均风速为3米每秒,有义波高为0.09的例子。
Bladed流的方向和风向是相反的,所以172度和-8度方向是一致的。
这个工况是一个十分钟工况,仿真时间用600秒,初始时间30秒。