RationalDMIS相对测量
在测量元素点，边界点、圆、圆弧和键槽，圆柱和圆锥时，请拖放作为参考测量的元素到测点管理窗口元素名称后面参考实际元素后面的编辑框中，然后进行元素测量，测量深度及相应的测量方向可以相对于实际值发生改变。 测量得到的实际位置与测量位置有一定的偏离，此元素的法向与相对参照元素法向一致。
DMIS语句：
The RMEAS statement signifies that a measurement of a feature is to be performed. The measurement sequence begins with anRMEAS statement and ends with the ENDMES statement. The RMEAS…ENDMES block may contain statements found in (Table 13 — DMIS statements allowed in a measurement block).
In the following examples, four points are taken in order to measure a circle called "RCIR_12":
Example 1
MODE/PROG,MAN
F(RPOINT_1)=FEAT/POINT,CART,-10.5,35.5,107.5,0.0,0.0,1.0
MEAS/POINT, F(RPOINT_1),1
PTMEAS/CART,-10.5,35.5,107.5,0.0,0.0,1.0
ENDMES
F(RCIR_12)=FEAT/CIRCLE,INNER,CART,-20.5,35.5,107.5,0.0,0.0,1.0,10
RMEAS/CIRCLE,F(RCIR_12),4,FA(RPOINT_1)
PTMEAS/CART,-15.5,35.5,107.5,-1,0,0
PTMEAS/CART,-25.5,35.5,107.5,1,0,0
GOTO/-20.5,35.5,107.5
PTMEAS/CART,-20.5,40.5,107.5,0,-1,0
PTMEAS/CART,-20.5,30.5,107.5,0,1,0
ENDMES
In example 1 theRMEAS statement signifies that a circle called "RCIR_12" is to be measured by taking four point measurements relative to a point called "RPOINT_1". The following statements specify that point measurements will be used, the location of the points to be taken, and an intermediate move. The nominal values for the circle measurement points is programmed, but the location that the machine measures the points will be adjusted relative to the deviation of the reference point as defined in theRMEAS ( input format 1 ) statement definition. The ENDMES statement signifies the end of the sequence.
Example 2
MODE/PROG,MAN
F(RPOINT_1)=FEAT/POINT,CART,-10.5,35.5,107.5,0.0,0.0,1.0
MEAS/POINT, F(RPOINT_1),1
PTMEAS/CART,-10.5,35.5,107.5,0.0,0.0,1.0
ENDMES
SCNMOD/ON
SCNSET/DRAG,.1
F(RCIR_12)=FEAT/CIRCLE,INNER,CART,-20.5,35.5,107.5,0.0,0.0,1.0,10
RMEAS/CIRCLE,F(RCIR_12),4,FA(RPOINT_1)
PTMEAS/CART,-15.5,35.5,107.5,-1,0,0
PTMEAS/CART,-25.5,35.5,107.5,1,0,0
GOTO/-20.5,35.5,107.5
PTMEAS/CART,-20.5,40.5,107.5,0,-1,0
PTMEAS/CART,-20.5,30.5,107.5,0,1,0
ENDMES
Example 2 is the same as example 1 above, except that the SCNMOD/ON statement explicitly activates scanning. Because the system is operating in programmed mode and scanning has been activated, the system will scan two arcs in the circle. The first arc will begin at the point defined in the first PTMEAS statement, and end at the point defined by the second PTMEAS statement. The system will then move to the point defined by the GOTO statement. The system will then scan the second arc, beginning at the point defined by the third PTMEAS statement, and ending at the point defined by the fourth PTMEAS statement. The system will collect measurement data based on the parameters set with the SCNSET statement and the number of measurement points in the RMEAS statement is ignored. All measurements are relative to feature FA(RPOINT_1) as required by the RMEAS statement.
生成的测量点位置，根据Rmeas/FA后面的窗口中拖放的参考元素的实际和理论的坐标位置及方向偏差来进行调整。
DMISMN/'Created by [Shanjianguozi] on 星期日, 一月 01, 2017', 4.0
UNITS/MM, ANGDEC
WKPLAN/XYPLAN
PRCOMP/ON
TECOMP/ON
FLY/1.000000
MODE/PROG, MAN
SNSET/APPRCH, 3.000000
SNSET/RETRCT, 3.000000
SNSET/DEPTH, 0.000000
SNSET/SEARCH, 10.000000
SNSET/CLRSRF, 20.000000
RECALL/D(MCS)
SNSLCT/S(PH10T)
GEOALG/CIRCLE, LSTSQR
GEOALG/ARC, LSTSQR
GEOALG/PLANE, LSTSQR
$$
$$
MODE/MAN
F(PLN1) = FEAT/PLANE,CART, 31.250000, 46.787796, 35.000000, 0.000000,$
0.000000, 1.000000
$$ Empty Meas Block
MEAS/PLANE, F(PLN1), 4
ENDMES
D(CRD1) = DATSET/FA(PLN1), ZDIR, ZORIG
D(CRD1) = TRANS/ZORIG, -35
F(LN1) = FEAT/LINE,BND,CART, 0.000000, 0.000000, 20.020814, 70.000000,$
0.000000, 20.020814, 0.000000, -1.000000, 0.000000
$$ Empty Meas Block
MEAS/LINE, F(LN1), 2
D(CRD2) = ROTATE/ZAXIS, FA(LN1), XDIR
F(PT1) = FEAT/POINT,CART, 0.000000, 23.520285, 29.561386, -1.000000,$
0.000000, 0.000000
$$ Empty Meas Block
MEAS/POINT, F(PT1), 1
ENDMES
D(CRD3) = TRANS/XORIG, FA(PT1), YORIG, FA(LN1)
$$ Set.CAD2PCS.CADM_1
MODE/PROG,MAN
SNSET/APPRCH, 3.0000
SNSET/RETRCT, 3.0000
SNSET/DEPTH, 0.0000
SNSET/SEARCH, 10.0000
SNSET/CLRSRF, 20.0000
F(CIR1) = FEAT/CIRCLE,INNER,CART, 40.000000, 55.000000, 33.000000, 0.000000,$
0.000000, 1.000000, 45.000000
$$ Measurement points are created through nominal points
MEAS/CIRCLE, F(CIR1), 4
PTMEAS/CART, 58.298938, 68.091939, 33.000000, -0.813286, -0.581864, 0.000000
GOTO/CART, 49.781112, 70.702861, 33.000000
GOTO/CART, 43.027344, 73.250622, 33.000000
GOTO/CART, 35.812691, 73.019890, 33.000000
PTMEAS/CART, 26.908061, 73.298938, 33.000000, 0.581864, -0.813286, 0.000000
GOTO/CART, 24.297139, 64.781112, 33.000000
GOTO/CART, 21.749378, 58.027344, 33.000000
GOTO/CART, 21.980110, 50.812691, 33.000000
PTMEAS/CART, 21.701062, 41.908061, 33.000000, 0.813286, 0.581864, 0.000000
GOTO/CART, 30.218888, 39.297139, 33.000000
GOTO/CART, 36.972656, 36.749378, 33.000000
GOTO/CART, 44.187309, 36.980110, 33.000000
PTMEAS/CART, 53.091939, 36.701062, 33.000000, -0.581864, 0.813286, 0.000000
ENDMES
CONST/POINT,F(CIR1),MOVEPT,FA(CIR1),F(CIR1),5.000000
F(CIR2) = FEAT/CIRCLE,INNER,CART, 25.000000, 7.908118, 27.928932, 0.000000,$
-0.707107, 0.707107, 15.000000
$$ Measurement points are created through nominal points
RMEAS/CIRCLE, F(CIR2), 4, FA(CIR1)
GOTO/CART, 50.764483, 11.617454, 56.336752
GOTO/CART, 27.451866, -2.675005, 42.044294
PTMEAS/CART, 30.253998, 11.692659, 31.713473, -0.700520, -0.504614, -0.504614
GOTO/CART, 26.309412, 10.203269, 30.224084
GOTO/CART, 24.967612, 10.382886, 30.403700
GOTO/CART, 23.630743, 10.185741, 30.206555
PTMEAS/CART, 19.647851, 11.623256, 31.644070, 0.713576, -0.495383, -0.495383
GOTO/CART, 21.754166, 8.834012, 28.854826
GOTO/CART, 21.500150, 7.885216, 27.906030
GOTO/CART, 21.778954, 6.939907, 26.960721
PTMEAS/CART, 19.746002, 4.123577, 24.144391, 0.700520, 0.504614, 0.504614
GOTO/CART, 23.690588, 5.612967, 25.633781
GOTO/CART, 25.032388, 5.433350, 25.454164
GOTO/CART, 26.369257, 5.630495, 25.651309
PTMEAS/CART, 30.352149, 4.192980, 24.213794, -0.713576, 0.495383, 0.495383
ENDMES
OUTPUT/FA(CIR2)
F(CYL1) = FEAT/CYLNDR,INNER,CART, 56.000000, 27.287187, 30.000000, 0.000000,$
0.000000, 1.000000, 10.000000, 10.000000
$$ Measurement points are created through nominal points
RMEAS/CYLNDR, F(CYL1), 8, FA(CIR1)
PTMEAS/CART, 56.000000, 32.287187, 26.250000, 0.000000, -1.000000, 0.000000
PTMEAS/CART, 56.000000, 32.287187, 33.750000, 0.000000, -1.000000, 0.000000
PTMEAS/CART, 60.330127, 29.787187, 28.750000, -0.866019, -0.500011, -0.000000
PTMEAS/CART, 60.330127, 24.787187, 28.750000, -0.866019, 0.500011, 0.000000
PTMEAS/CART, 56.000000, 22.287187, 26.250000, 0.000000, 1.000000, 0.000000
PTMEAS/CART, 56.000000, 22.287187, 33.750000, 0.000000, 1.000000, 0.000000
PTMEAS/CART, 51.669873, 24.787187, 28.750000, 0.866019, 0.500011, 0.000000
PTMEAS/CART, 51.669873, 29.787187, 28.750000, 0.866019, -0.500011, 0.000000
ENDMES
OUTPUT/FA(CYL1)
F(CIR3) = FEAT/CIRCLE,INNER,CART, 50.000000, 7.908118, 27.928932, -0.000000,$
-0.707107, 0.707107, 15.000000
$$ Measurement points are created through nominal points
RMEAS/CIRCLE, F(CIR3), 4, FA(CYL1)
GOTO/CART, 55.133949, 5.908922, 50.628221
GOTO/CART, 50.951538, -2.059468, 42.659831
PTMEAS/CART, 52.039009, 13.011668, 33.032482, -0.271888, -0.680469, -0.680469
GOTO/CART, 49.590163, 10.365966, 30.386780
GOTO/CART, 48.291182, 10.067972, 30.088787
GOTO/CART, 47.252353, 9.441160, 29.461975
PTMEAS/CART, 42.782491, 9.349915, 29.370729, 0.962347, -0.192209, -0.192209
GOTO/CART, 46.524078, 7.618319, 27.639134
GOTO/CART, 46.945505, 6.699801, 26.720615
GOTO/CART, 47.831951, 5.965238, 25.986053
PTMEAS/CART, 47.960991, 2.804568, 22.825382, 0.271888, 0.680469, 0.680469
GOTO/CART, 50.409837, 5.450270, 25.471084
GOTO/CART, 51.708818, 5.748264, 25.769078
GOTO/CART, 52.747647, 6.375075, 26.395890
PTMEAS/CART, 57.217509, 6.466321, 26.487135, -0.962347, 0.192209, 0.192209
ENDMES
OUTPUT/FA(CIR3)
(PT2) = FEAT/POINT,CART, 8.090393, 35.421658, 35.000000, 0.000000,$
0.000000, 1.000000
MEAS/POINT, F(PT2), 1
PTMEAS/CART, 8.090393, 35.421658, 35.000000, 0.000000, 0.000000, 1.000000
ENDMES
CONST/POINT,F(PT2),MOVEPT,FA(PT2),F(PT2),5.000000
F(CIR4) = FEAT/CIRCLE,INNER,CART, 72.000000, 55.000000, 35.000000, 0.000000,$
0.000000, 1.000000, 10.000000
$$ Measurement points are created through nominal points
RMEAS/CIRCLE, F(CIR4), 4, FA(PT2)
GOTO/CART, 8.090393, 35.421658, 51.000000
GOTO/CART, 71.043859, 54.707092, 51.000000
PTMEAS/CART, 67.219297, 53.535459, 35.000000, 0.956139, 0.292912, 0.000000
PTMEAS/CART, 73.464541, 50.219297, 35.000000, -0.292912, 0.956139, 0.000000
PTMEAS/CART, 76.780703, 56.464541, 35.000000, -0.956139, -0.292912, 0.000000
PTMEAS/CART, 70.535459, 59.780703, 35.000000, 0.292912, -0.956139, 0.000000
ENDMES
OUTPUT/FA(CIR4)
