RationalDMIS极坐标测量_ACT_UG-仿真秀干货文章

RationalDMIS极坐标测量

17小时前浏览2

测量一个元素时，有两种坐标系统卡笛尔直角坐标系和极坐标可供选择。卡笛尔坐标系用 X，Y和 Z参数来定位元素，极坐标系用角度(A)，半径(R)，和 H参数定位元素。极坐标基于极点进行计算。极点是元素的原点。半径(R)是被测元素和极点之间的距离。高度(H)取决于当前工作面的位置。例如，测量 XY工作面上的元素，其极坐标为 A, R, Z;；假如测的元素在 YZ工作面上，其极坐标为 A, R, X；最后，ZX工作面上的元素是 A, R, Y。如下图所示，为圆 1，圆 2和圆 3的极坐标测量。

实际工作中，很多时候用极半径（R）和极角(A)，编程测量特征比较方便，尤其是只给了特征分度圆半径（直径）和等分数（角度标注）的时候。评价的时候，输出结果，根据自己需要进行输出。

DMISMN/'Created by [天永智能装备股份有限公司] on 星期六, 一月 06, 2018', 4.0

UNITS/MM, ANGDEC

WKPLAN/XYPLAN

PRCOMP/ON

TECOMP/ON

FLY/1.0

MODE/PROG, MAN

SNSET/APPRCH, 3.000000

SNSET/RETRCT, 3.000000

SNSET/DEPTH, 0.000000

SNSET/SEARCH, 10.000000

SNSET/CLRSRF, 50.000000

RECALL/D(MCS)

SNSLCT/S(20-30X2)

GEOALG/CIRCLE, LSTSQR

GEOALG/ARC, LSTSQR

GEOALG/PLANE, LSTSQR

MODE/MAN

F(PLN1) = FEAT/PLANE,CART, 464.3560, -884.1594, -663.7665, 0.000428,$

0.000165, 1.000000

$$ Measurement points are created through actual points

MEAS/PLANE, F(PLN1), 4

PTMEAS/CART, 415.499961, -818.708356, -663.756383, 0.000428, 0.000165,$

1.000000

PTMEAS/CART, 402.885688, -945.220521, -663.730155, 0.000428, 0.000165,$

1.000000

PTMEAS/CART, 519.772254, -945.219448, -663.780228, 0.000428, 0.000165,$

1.000000

PTMEAS/CART, 519.266245, -827.489473, -663.799390, 0.000428, 0.000165,$

1.000000

ENDMES

D(CRD1) = DATSET/FA(PLN1), ZDIR

D(CRD1) = TRANS/ZORIG, FA(PLN1)

F(CIR1) = FEAT/CIRCLE,INNER,CART, 461.5721, -965.5117, -2.5498, -0.000000,$

-0.000000, 1.000000, 22.0427

$$ Measurement points are created through actual points

MEAS/CIRCLE, F(CIR1), 4

PTMEAS/CART, 459.188251, -954.751311, -2.549747, 0.216300, -0.976327,$

-0.000000

PTMEAS/CART, 472.589988, -965.233169, -2.549747, -0.999681, -0.025276,$

-0.000000

PTMEAS/CART, 464.451720, -976.150273, -2.549747, -0.261271, 0.965266,$

-0.000000

PTMEAS/CART, 450.652646, -967.006477, -2.549747, 0.990761, 0.135621,$

-0.000000

ENDMES

F(CIR2) = FEAT/CIRCLE,INNER,CART, 527.4545, -853.5610, -2.0757, -0.000000,$

-0.000000, 1.000000, 22.0295

$$ Measurement points are created through actual points

MEAS/CIRCLE, F(CIR2), 4

PTMEAS/CART, 522.763676, -843.595044, -2.075712, 0.425870, -0.904784,$

-0.000000

PTMEAS/CART, 536.697803, -847.570434, -2.075712, -0.839170, -0.543870,$

-0.000000

PTMEAS/CART, 531.285416, -863.888163, -2.075712, -0.347794, 0.937571,$

-0.000000

PTMEAS/CART, 516.626846, -855.582473, -2.075712, 0.983016, 0.183521,$

-0.000000

ENDMES

F(CIR3) = FEAT/CIRCLE,INNER,CART, 397.5611, -852.4786, -2.0691, -0.000000,$

-0.000000, 1.000000, 22.0324

$$ Measurement points are created through actual points

MEAS/CIRCLE, F(CIR3), 4

PTMEAS/CART, 394.750299, -841.827089, -2.069040, 0.255157, -0.966900,$

-0.000000

PTMEAS/CART, 406.483036, -846.016703, -2.069040, -0.809888, -0.586585,$

-0.000000

PTMEAS/CART, 402.142146, -862.497171, -2.069040, -0.415841, 0.909437,$

-0.000000

PTMEAS/CART, 387.519905, -857.009596, -2.069040, 0.911500, 0.411300,$

-0.000000

ENDMES

TEXT/OPER, '切换坐标系为极坐标系！'

F(CIR1) = FEAT/CIRCLE,INNER,POL, 75.0000, -0.0000, -2.5498, -0.000000,$

-0.000000, 1.000000, 22.0000

F(CIR2) = FEAT/CIRCLE,INNER,POL, 75.0000, 120.0000, -2.0757, -0.000000,$

-0.000000, 1.000000, 22.0000

F(CIR3) = FEAT/CIRCLE,INNER,POL, 75.0000, 240.0000, -2.0691, -0.000000,$

-0.000000, 1.000000, 22.0000

$$ This sample DMIS Macro is provided by External-Array Software, Inc.

$$ It should be modified for your own use. There is no guarantee for

$$ the quality of this Macro. November, 2003

$$ FUNCION: Move machine CLEAR DIST above the current clear surface

$$ plane and then move machine parallel to the clear surface

$$ plane to the project point of POINT(TARX, TARY, TARZ) on

$$ the clear surface plane but CLEAR DIST above the plane

$$ ALL Macro parameters are in PCS and Current UNITS

$$ Last update: 3-1-04 Add mode checking. only works in PROG MODE

$$ Last update: 8-24-04 Clear position is based on the surface of

$$ ruby ball instead of the center of it.

M(EASI_CLEARPLN_GOTO) = MACRO/ISNOM, TARX, TARY, TARZ

DECL/LOCAL, REAL, CCX, CCY, CCZ, CCI, CCJ, CCK

DECL/LOCAL, REAL, CURX, CURY, CURZ, TD, CLRDIST, SDIAM

DECL/LOCAL, CHAR, 255, CLRLABEL, FLABEL, MMODE, SNAME

MMODE = VALUE/MODE

CLRLABEL = VALUE/SNSET, CLRSRF

IF/ ( (LEN(CLRLABEL) .GT. 0) .AND. (MMODE .EQ. 'PROG,MAN') )

CLRDIST = VALUE/SNSET, CLRSRF, DIST

FLABEL = ASSIGN/'FA'

IF/ ISNOM .EQ. 0

FLABEL = ASSIGN/'F'

ENDIF

CCX = OBTAIN/FLABEL(@CLRLABEL), 3

CCY = OBTAIN/FLABEL(@CLRLABEL), 4

CCZ = OBTAIN/FLABEL(@CLRLABEL), 5

CCI = OBTAIN/FLABEL(@CLRLABEL), 6

CCJ = OBTAIN/FLABEL(@CLRLABEL), 7

CCK = OBTAIN/FLABEL(@CLRLABEL), 8

SNAME = VALUE/SNSLCT

SDIAM = OBTAIN/SS(SNAME), 8

CCX = ASSIGN/CCX + CCI * SDIAM/2

CCY = ASSIGN/CCY + CCJ * SDIAM/2

CCZ = ASSIGN/CCZ + CCK * SDIAM/2

CURX = VALUE/GOTO, XAXIS

CURY = VALUE/GOTO, YAXIS

CURZ = VALUE/GOTO, ZAXIS

TD = ASSIGN/(CURX - CCX) * CCI + (CURY - CCY) * CCJ + (CURZ - CCZ) * CCK

IF/ TD .LT. CLRDIST

TD = ASSIGN/(CLRDIST - TD)

GOTO/CURX+CCI*TD, CURY+CCJ*TD, CURZ+CCK*TD

ENDIF

TD = ASSIGN/(TARX - CCX) * CCI + (TARY - CCY) * CCJ + (TARZ - CCZ) * CCK

IF/ TD .LT. CLRDIST

TD = ASSIGN/(CLRDIST - TD)

GOTO/TARX+CCI*TD, TARY+CCJ*TD, TARZ+CCK*TD

ENDIF

ENDMAC

DMESW/COMAND,'D(CRD2) = LOCATE/XYDIR, ZAXIS, FA(CIR1), XYZAXI, FA(CIR2),$

XYZAXI, FA(CIR3), XYZAXI'

MODE/PROG,MAN

SNSET/APPRCH, 3

SNSET/RETRCT, 3

SNSET/DEPTH, 0.0000

SNSET/SEARCH, 10.0000

SNSET/CLRSRF, 50

GOTO/-34.208994, -16.445303, 163.389464

GOTO/-68.550425, -50.072598, 27.279141

F(PLN2) = FEAT/PLANE,CART, -15.7122, -8.6084, -0.0016, 0.000088, -0.000008,$

1.000000

$$ Measurement points are created through actual points

MEAS/PLANE, F(PLN2), 4

PTMEAS/CART, -68.556478, -50.024193, 0.002707, 0.000088, -0.000008, 1.000000

GOTO/CART, -68.546796, -50.036983, 34.988226

GOTO/CART, -69.172372, 25.218074, 35.000465

PTMEAS/CART, -69.182607, 25.236864, 0.003335, 0.000088, -0.000008, 1.000000

GOTO/CART, -69.167794, 25.209764, 57.061661

GOTO/CART, 22.725162, 58.380142, 57.068372

PTMEAS/CART, 22.696791, 58.413635, -0.004528, 0.000088, -0.000008, 1.000000

GOTO/CART, 22.710982, 58.389930, 54.675857

GOTO/CART, 52.201588, -68.084717, 54.620893

PTMEAS/CART, 52.193402, -68.059981, -0.008095, 0.000088, -0.000008, 1.000000

GOTO/CART, 52.208593, -68.087660, 62.550963

GOTO/CART, 10.211719, -9.866483, 185.461005

ENDMES

F(CIR4) = FEAT/CIRCLE,INNER,POL, 75.0000, 0.0000, -3.0000, 0.000000,$

0.000000, 1.000000, 22.0000

$$ Measurement points are created through nominal points

MEAS/CIRCLE, F(CIR4), 4

GOTO/POL, 68.080678, 359.114565, 47.993117

GOTO/POL, 68.080678, 359.114565, 47.000000

PTMEAS/POL, 64.145965, 358.524600, -3.000000, 0.988671, 0.150096, -0.000000

GOTO/POL, 68.217930, 1.410360, -3.000000

GOTO/POL, 69.481950, 3.427927, -3.000000

GOTO/POL, 71.628533, 4.803053, -3.000000

PTMEAS/POL, 74.150239, 8.433751, -3.000000, 0.150096, -0.988671, 0.000000

GOTO/POL, 76.980212, 5.069838, -3.000000

GOTO/POL, 79.355376, 4.077315, -3.000000

GOTO/POL, 81.078512, 2.561118, -3.000000

PTMEAS/POL, 85.891182, 1.101817, -3.000000, -0.988671, -0.150096, 0.000000

GOTO/POL, 81.819966, 358.824139, -3.000000

GOTO/POL, 80.749312, 357.050847, -3.000000

GOTO/POL, 78.851418, 355.637808, -3.000000

PTMEAS/POL, 77.419262, 351.924794, -3.000000, -0.150096, 0.988671, 0.000000

GOTO/POL, 76.366914, 354.795389, 47.000000

ENDMES

F(CIR5) = FEAT/CIRCLE,INNER,POL, 75.0000, 120.0000, -3.0000, 0.000000,$

0.000000, 1.000000, 22.0000

$$ Measurement points are created through nominal points

MEAS/CIRCLE, F(CIR5), 4

GOTO/POL, 76.364257, 354.806225, 47.993117

GOTO/POL, 78.640842, 124.467516, 47.993117

GOTO/POL, 78.640842, 124.467516, 47.000000

PTMEAS/POL, 80.914088, 126.825673, -3.000000, 0.999861, 0.016699, 0.000000

GOTO/POL, 80.604999, 123.098917, -3.000000

GOTO/POL, 81.759678, 121.349813, -3.000000

GOTO/POL, 81.965098, 119.441631, -3.000000

PTMEAS/POL, 84.784918, 116.388551, -3.000000, 0.016699, -0.999861, 0.000000

GOTO/POL, 79.546977, 116.044611, -3.000000

GOTO/POL, 77.220413, 114.994944, -3.000000

GOTO/POL, 74.527050, 114.640470, -3.000000

PTMEAS/POL, 70.320057, 112.139942, -3.000000, -0.999861, -0.016699,$

-0.000000

GOTO/POL, 69.649314, 116.413036, -3.000000

GOTO/POL, 68.290174, 118.383886, -3.000000

GOTO/POL, 68.043483, 120.672616, -3.000000

PTMEAS/POL, 65.601201, 124.669620, -3.000000, -0.016699, 0.999861, -0.000000

GOTO/POL, 68.958324, 122.827706, 47.000000

ENDMES

F(CIR6) = FEAT/CIRCLE,INNER,POL, 75.0000, 240.0000, -3.0000, 0.000000,$

0.000000, 1.000000, 22.0000

$$ Measurement points are created through nominal points

MEAS/CIRCLE, F(CIR6), 4

GOTO/POL, 68.971279, 122.822135, 47.993117

GOTO/POL, 78.833316, 235.628455, 47.993117

GOTO/POL, 78.833316, 235.628455, 47.000000

PTMEAS/POL, 81.207588, 233.329228, -3.000000, 0.999862, 0.016599, 0.000000

GOTO/POL, 76.345339, 234.791427, -3.000000

GOTO/POL, 73.613902, 234.701860, -3.000000

GOTO/POL, 71.050949, 235.455852, -3.000000

PTMEAS/POL, 65.810252, 235.068100, -3.000000, 0.016599, -0.999862, 0.000000

GOTO/POL, 68.077042, 239.133006, -3.000000

GOTO/POL, 68.223818, 241.428346, -3.000000

GOTO/POL, 69.496194, 243.441978, -3.000000

PTMEAS/POL, 69.980910, 247.747037, -3.000000, -0.999862, -0.016599, 0.000000

GOTO/POL, 74.293890, 245.352810, -3.000000

GOTO/POL, 77.001210, 245.064450, -3.000000

GOTO/POL, 79.372259, 244.066895, -3.000000

PTMEAS/POL, 84.622755, 243.833614, -3.000000, -0.016599, 0.999862, 0.000000

GOTO/POL, 81.089107, 242.547324, 47.000000

ENDMES

F(PROJCI1) = FEAT/CIRCLE,INNER,POL, 75, 0, -0.0000, 0.000000,$

-0.000000, 1.000000, 22.0000

CONST/CIRCLE,F(PROJCI1),PROJCT,FA(CIR4),FA(PLN2)

F(PROJCI2) = FEAT/CIRCLE,INNER,POL, 75, 120, 0.0000, 0.0000,$

-0.000000, 1.000000, 22.0000

CONST/CIRCLE,F(PROJCI2),PROJCT,FA(CIR5),FA(PLN2)

F(PROJCI3) = FEAT/CIRCLE,INNER,POL, 75, 240.000 , -0.0000, 0.000000,$

-0.000000, 1.000000, 22.0000

CONST/CIRCLE,F(PROJCI3),PROJCT,FA(CIR6),FA(PLN2)

DMESW/COMAND,'D(CRD3) = LOCATE/XYDIR, ZAXIS, FA(PROJCI1), XYZAXI,$

FA(PROJCI2), XYZAXI, FA(PROJCI3), XYZAXI'

MODE/PROG,MAN

SNSET/APPRCH, 3

SNSET/RETRCT, 3

SNSET/DEPTH, 0.0000

SNSET/SEARCH, 10.0000

SNSET/CLRSRF, 50

F(J-1) = FEAT/CIRCLE,INNER,POL, 75.0000, 0.0000, -3.0000, 0.000000,$

0.000000, 1.000000, 22.0000

$$ Measurement points are created through nominal points

MEAS/CIRCLE, F(J-1), 4

GOTO/POL, 81.078468, 242.539042, 47.993117

GOTO/POL, 67.994177, 359.902207, 47.993117

GOTO/POL, 67.994177, 359.902207, 47.000000

PTMEAS/POL, 64.001768, 359.836900, -3.000000, 0.999862, 0.016599, 0.000000

GOTO/POL, 68.531310, 2.152365, -3.000000

GOTO/POL, 70.133422, 3.983304, -3.000000

GOTO/POL, 72.497283, 5.087005, -3.000000

PTMEAS/POL, 75.621899, 8.362792, -3.000000, 0.016599, -0.999862, 0.000000

GOTO/POL, 77.847101, 4.802188, -3.000000

GOTO/POL, 80.030478, 3.607777, -3.000000

GOTO/POL, 81.475941, 1.961159, -3.000000

PTMEAS/POL, 85.998684, 0.121382, -3.000000, -0.999862, -0.016599, -0.000000

GOTO/POL, 81.557663, 358.191535, -3.000000

GOTO/POL, 80.184137, 356.516645, -3.000000

GOTO/POL, 78.053422, 355.275962, -3.000000

PTMEAS/POL, 75.982422, 351.677170, -3.000000, -0.016599, 0.999862, 0.000000

GOTO/POL, 75.442059, 354.671554, 47.000000

ENDMES

F(J-2) = FEAT/CIRCLE,INNER,POL, 75.0000, 120.0000, -3.0000, 0.000000,$

0.000000, 1.000000, 22.0000

$$ Measurement points are created through nominal points

MEAS/CIRCLE, F(J-2), 4

GOTO/POL, 75.440089, 354.682356, 47.993117

GOTO/POL, 78.641348, 124.467271, 47.993117

GOTO/POL, 78.641348, 124.467271, 47.000000

PTMEAS/POL, 80.914861, 126.825277, -3.000000, 0.999862, 0.016599, 0.000000

GOTO/POL, 80.605351, 123.098564, -3.000000

GOTO/POL, 81.759832, 121.349401, -3.000000

GOTO/POL, 81.965034, 119.441208, -3.000000

PTMEAS/POL, 84.784509, 116.387969, -3.000000, 0.016599, -0.999862, 0.000000

GOTO/POL, 79.546528, 116.044316, -3.000000

GOTO/POL, 77.219846, 114.994783, -3.000000

GOTO/POL, 74.526442, 114.640480, -3.000000

PTMEAS/POL, 70.319167, 112.140223, -3.000000, -0.999862, -0.016599,$

-0.000000

GOTO/POL, 69.648907, 116.413407, -3.000000

GOTO/POL, 68.289990, 118.384372, -3.000000

GOTO/POL, 68.043559, 120.673123, -3.000000

PTMEAS/POL, 65.601731, 124.670313, -3.000000, -0.016599, 0.999862, 0.000000

GOTO/POL, 68.958645, 122.828135, 47.000000

ENDMES

F(J-3) = FEAT/CIRCLE,INNER,POL, 75.0000, 240.0000, -3.0000, 0.000000,$

0.000000, 1.000000, 22.0000

$$ Measurement points are created through nominal points

MEAS/CIRCLE, F(J-3), 4

GOTO/POL, 68.970363, 122.822691, 47.993117

GOTO/POL, 78.832826, 235.628203, 47.993117

GOTO/POL, 78.832826, 235.628203, 47.000000

PTMEAS/POL, 81.206842, 233.328823, -3.000000, 0.999862, 0.016599, 0.000000

GOTO/POL, 76.344756, 234.791321, -3.000000

GOTO/POL, 73.613309, 234.701931, -3.000000

GOTO/POL, 71.050441, 235.456109, -3.000000

PTMEAS/POL, 65.809700, 235.068764, -3.000000, 0.016599, -0.999862, 0.000000

GOTO/POL, 68.076945, 239.133504, -3.000000

GOTO/POL, 68.223978, 241.428832, -3.000000

GOTO/POL, 69.496580, 243.442357, -3.000000

PTMEAS/POL, 69.981775, 247.747341, -3.000000, -0.999862, -0.016599,$

-0.000000

GOTO/POL, 74.294488, 245.352835, -3.000000

GOTO/POL, 77.001776, 245.064304, -3.000000

GOTO/POL, 79.372714, 244.066613, -3.000000

PTMEAS/POL, 84.623184, 243.833046, -3.000000, -0.016599, 0.999862, 0.000000

GOTO/POL, 81.089392, 242.546951, 47.000000

ENDMES

F(J-4) = FEAT/CIRCLE,INNER,POL, 0.0000, 0.0000, -3.0000, 0.000000, 0.000000,$

1.000000, 50.0000

$$ Measurement points are created through nominal points

MEAS/CIRCLE, F(J-4), 4

GOTO/POL, 81.077243, 242.542183, 47.993117

GOTO/POL, 21.006883, 180.949100, 47.993117

GOTO/POL, 21.006883, 180.949100, 47.000000

PTMEAS/POL, 25.000000, 180.949100, -3.000000, 0.999862, 0.016599, 0.000000

GOTO/POL, 21.006883, 158.449100, -3.000000

GOTO/POL, 21.006883, 135.949100, -3.000000

GOTO/POL, 21.006883, 113.449100, -3.000000

PTMEAS/POL, 25.000000, 90.949100, -3.000000, 0.016599, -0.999862, 0.000000

GOTO/POL, 21.006883, 68.449100, -3.000000

GOTO/POL, 21.006883, 45.949100, -3.000000

GOTO/POL, 21.006883, 23.449100, -3.000000

PTMEAS/POL, 25.000000, 0.949100, -3.000000, -0.999862, -0.016599, -0.000000

GOTO/POL, 21.006883, 338.449100, -3.000000

GOTO/POL, 21.006883, 315.949100, -3.000000

GOTO/POL, 21.006883, 293.449100, -3.000000

PTMEAS/POL, 25.000000, 270.949100, -3.000000, -0.016599, 0.999862, 0.000000

GOTO/POL, 21.006883, 270.949100, 47.000000

ENDMES

F(J-5) = FEAT/CIRCLE,INNER,POL, 43.5000, 112.0000, -3.0000, 0.000000,$

0.000000, 1.000000, 20.0000

$$ Measurement points are created through nominal points

MEAS/CIRCLE, F(J-5), 4

GOTO/POL, 20.992943, 270.944966, 47.993117

GOTO/POL, 46.000543, 118.999915, 47.993117

GOTO/POL, 46.000543, 118.999915, 47.000000

PTMEAS/POL, 48.007850, 123.209532, -3.000000, 0.999862, 0.016599, 0.000000

GOTO/POL, 47.837261, 117.221575, -3.000000

GOTO/POL, 49.050379, 114.849389, -3.000000

GOTO/POL, 49.505196, 112.175795, -3.000000

PTMEAS/POL, 52.954574, 108.110547, -3.000000, 0.016599, -0.999862, 0.000000

GOTO/POL, 48.032195, 107.056918, -3.000000

GOTO/POL, 46.265185, 105.185340, -3.000000

GOTO/POL, 44.062992, 104.167281, -3.000000

PTMEAS/POL, 40.984709, 98.837742, -3.000000, -0.999862, -0.016599, -0.000000

GOTO/POL, 39.601285, 105.688451, -3.000000

GOTO/POL, 38.088393, 108.329549, -3.000000

GOTO/POL, 37.495345, 111.767897, -3.000000

PTMEAS/POL, 34.355686, 118.001423, -3.000000, -0.016599, 0.999862, 0.000000

GOTO/POL, 37.955390, 115.258880, 47.000000

ENDMES

F(J-6) = FEAT/CIRCLE,INNER,POL, 43.5000, 292.0000, -3.0000, 0.000000,$

0.000000, 1.000000, 20.0000

$$ Measurement points are created through nominal points

MEAS/CIRCLE, F(J-6), 4

GOTO/POL, 37.968551, 115.252958, 47.993117

GOTO/POL, 41.720696, 284.277831, 47.993117

GOTO/POL, 41.720696, 284.277831, 47.000000

PTMEAS/POL, 40.984732, 278.837737, -3.000000, 0.999862, 0.016599, 0.000000

GOTO/POL, 39.601296, 285.688439, -3.000000

GOTO/POL, 38.088399, 288.329530, -3.000000

GOTO/POL, 37.495346, 291.767875, -3.000000

PTMEAS/POL, 34.355675, 298.001388, -3.000000, 0.016599, -0.999862, 0.000000

GOTO/POL, 39.364612, 298.035145, -3.000000

GOTO/POL, 41.427006, 299.614991, -3.000000

GOTO/POL, 43.762048, 299.886924, -3.000000

PTMEAS/POL, 48.007830, 303.209547, -3.000000, -0.999862, -0.016599,$

-0.000000

GOTO/POL, 47.837252, 297.221588, -3.000000

GOTO/POL, 49.050373, 294.849404, -3.000000

GOTO/POL, 49.505195, 292.175812, -3.000000

PTMEAS/POL, 52.954581, 288.110571, -3.000000, -0.016599, 0.999862, 0.000000

GOTO/POL, 49.153373, 289.484112, 47.000000

ENDMES

T(TCORTOL1) = TOL/CORTOL,RADIAL, -0.0200, 0.0200

T(TCORTOL2) = TOL/CORTOL,ANGLE, -0.0200, 0.0200

OUTPUT/FA(J-1),TA(TCORTOL1),TA(TCORTOL2)

OUTPUT/FA(J-2),TA(TCORTOL1),TA(TCORTOL2)

OUTPUT/FA(J-3),TA(TCORTOL1),TA(TCORTOL2)

OUTPUT/FA(J-4),TA(TCORTOL1),TA(TCORTOL2)

OUTPUT/FA(J-5),TA(TCORTOL1),TA(TCORTOL2)

OUTPUT/FA(J-6),TA(TCORTOL1),TA(TCORTOL2)

TEXT/OPER, '翻面测量！'

RECALL/D(MCS)

MODE/MAN

F(PLN3) = FEAT/PLANE,CART, 463.5256, -893.2781, -663.7959, 0.000081,$

-0.000292, 1.000000

$$ Measurement points are created through actual points

MEAS/PLANE, F(PLN3), 4

PTMEAS/CART, 428.142585, -825.193528, -663.773174, 0.000081, -0.000292,$

1.000000

PTMEAS/CART, 508.511853, -827.840536, -663.780466, 0.000081, -0.000292,$

1.000000

PTMEAS/CART, 508.558352, -963.477880, -663.820054, 0.000081, -0.000292,$

1.000000

PTMEAS/CART, 408.889660, -956.600297, -663.809963, 0.000081, -0.000292,$

1.000000

ENDMES

D(CRD4) = DATSET/FA(PLN3), -ZDIR

D(CRD4) = TRANS/ZORIG, FA(PLN3)

$$ Measurement points are created through actual points

F(P-1) = FEAT/CIRCLE,INNER,CART, -114.4819, 1067.0033, 9.6660, -0.000000,$

-0.000000, -1.000000, 22.0342

$$ Measurement points are created through actual points

MEAS/CIRCLE, F(P-1), 4

PTMEAS/CART, -112.948497, 1056.093466, 9.665998, -0.139178, 0.990267,$

-0.000000

PTMEAS/CART, -104.421031, 1071.493028, 9.665998, -0.913198, -0.407517,$

-0.000000

PTMEAS/CART, -119.049099, 1077.029183, 9.665998, 0.414560, -0.910022,$

-0.000000

PTMEAS/CART, -125.249559, 1064.672450, 9.665998, 0.977362, 0.211572,$

-0.000000

ENDMES

F(P-2) = FEAT/CIRCLE,INNER,CART, -90.2563, 939.3790, 9.6755, -0.000000,$

-0.000000, -1.000000, 22.0434

$$ Measurement points are created through actual points

MEAS/CIRCLE, F(P-2), 4

PTMEAS/CART, -87.781963, 928.638677, 9.675482, -0.224495, 0.974475,$

-0.000000

PTMEAS/CART, -79.416826, 941.374987, 9.675482, -0.983466, -0.181093,$

-0.000000

PTMEAS/CART, -95.729614, 948.945643, 9.675482, 0.496598, -0.867981,$

-0.000000

PTMEAS/CART, -99.050842, 932.735763, 9.675482, 0.797933, 0.602746, -0.000000

ENDMES

F(P-3) = FEAT/CIRCLE,INNER,CART, 8.1480, 1024.1713, 10.7217, -0.000000,$

-0.000000, -1.000000, 22.0433

$$ Measurement points are created through actual points

MEAS/CIRCLE, F(P-3), 4

PTMEAS/CART, 9.946141, 1013.297355, 10.721796, -0.163141, 0.986603,$

-0.000000

PTMEAS/CART, 18.699462, 1027.356408, 10.721796, -0.957334, -0.288983,$

-0.000000

PTMEAS/CART, 5.107827, 1034.765385, 10.721796, 0.275842, -0.961203,$

-0.000000

PTMEAS/CART, -1.244447, 1018.404407, 10.721796, 0.852187, 0.523237,$

-0.000000

ENDMES

F(P-1) = FEAT/CIRCLE,INNER,POL, 75.0000, 0.0000, 9.6660, -0.000000,$

-0.000000, -1.000000, 22.0000

F(P-2) = FEAT/CIRCLE,INNER,POL, 75.0000, 120.0000, 9.6755, -0.000000,$

-0.000000, -1.000000, 22.0000

F(P-3) = FEAT/CIRCLE,INNER,POL, 75.0000, 240.0000, 10.7217, -0.000000,$

-0.000000, -1.000000, 22.0000

DMESW/COMAND,'D(CRD5) = LOCATE/XYDIR, ZAXIS, FA(P-1), XYZAXI, FA(P-2),$

XYZAXI, FA(P-3), XYZAXI'

MODE/PROG,MAN

SNSET/APPRCH, 3

SNSET/RETRCT, 3

SNSET/DEPTH, 0.0000

SNSET/SEARCH, 10.0000

SNSET/CLRSRF, 50

GOTO/12.557555, 10.649547, -138.381327

GOTO/-66.132074, 48.845187, -35.503403

F(PLN4) = FEAT/PLANE,CART, -15.4265, 6.8131, -0.0019, -0.000013, -0.000023,$

-1.000000

$$ Measurement points are created through nominal points

MEAS/PLANE, F(PLN4), 4

GOTO/CART, 78.995466, 5.756098, 7.006883

PTMEAS/CART, 81.272422, 9.036411, 11.000000, -0.570203, -0.821504, 0.000000

GOTO/CART, 80.894093, 3.788943, 11.000000

GOTO/CART, 81.895397, 1.244955, 11.000000

GOTO/CART, 81.846940, -1.488565, 11.000000

PTMEAS/CART, 84.036411, -6.272422, 11.000000, -0.821504, 0.570203, 0.000000

GOTO/CART, 78.788942, -5.894093, 11.000000

GOTO/CART, 76.244955, -6.895398, 11.000000

GOTO/CART, 73.511435, -6.846940, 11.000000

PTMEAS/CART, 68.727579, -9.036411, 11.000000, 0.570203, 0.821504, -0.000000

GOTO/CART, 69.105908, -3.788943, 11.000000

GOTO/CART, 68.104603, -1.244955, 11.000000

GOTO/CART, 68.153061, 1.488565, 11.000000

PTMEAS/CART, 65.963588, 6.272422, 11.000000, 0.821504, -0.570203, 0.000000

ENDMES

F(K-1) = FEAT/CIRCLE,INNER,POL, 75.0000, 0.0000, 11.0000, 0.000000,$

0.000000, -1.000000, 22.0000

$$ Measurement points are created through nominal points

MEAS/CIRCLE, F(K-1), 4

GOTO/POL, 82.006883, 0.000000, -39.993117

GOTO/POL, 82.006883, 0.000000, -39.000000

PTMEAS/POL, 86.000000, 0.000000, 11.000000, -1.000000, -0.000000, 0.000000

GOTO/POL, 81.517629, 1.885011, 11.000000

GOTO/POL, 80.107981, 3.545961, 11.000000

GOTO/POL, 77.950684, 4.763689, 11.000000

PTMEAS/POL, 75.802375, 8.343892, 11.000000, -0.000000, -1.000000, 0.000000

GOTO/POL, 72.607739, 5.115134, 11.000000

GOTO/POL, 70.220397, 4.046041, 11.000000

GOTO/POL, 68.578925, 2.240821, 11.000000

PTMEAS/POL, 64.000000, 0.000000, 11.000000, 1.000000, 0.000000, 0.000000

GOTO/POL, 68.578925, 357.759179, 11.000000

GOTO/POL, 70.220397, 355.953959, 11.000000

GOTO/POL, 72.607739, 354.884866, 11.000000

PTMEAS/POL, 75.802375, 351.656108, 11.000000, 0.000000, 1.000000, -0.000000

GOTO/POL, 75.326598, 354.662628, -39.000000

ENDMES

F(K-2) = FEAT/CIRCLE,INNER,POL, 75.0000, 120.0000, 11.0000, 0.000000,$

0.000000, -1.000000, 22.0000

$$ Measurement points are created through nominal points

MEAS/CIRCLE, F(K-2), 4

GOTO/POL, 75.324077, 354.651055, -39.993117

GOTO/POL, 71.753601, 115.148755, -39.993117

GOTO/POL, 71.753601, 115.148755, -39.000000

PTMEAS/POL, 70.149829, 112.195178, 11.000000, -1.000000, -0.000000, 0.000000

GOTO/POL, 74.410403, 114.643079, 11.000000

GOTO/POL, 77.111105, 114.964603, 11.000000

GOTO/POL, 79.460201, 115.988380, 11.000000

PTMEAS/POL, 84.705024, 116.277089, 11.000000, -0.000000, -1.000000, 0.000000

GOTO/POL, 81.952041, 119.360563, 11.000000

GOTO/POL, 81.788240, 121.270535, 11.000000

GOTO/POL, 80.671787, 123.030923, 11.000000

PTMEAS/POL, 81.061714, 126.748926, 11.000000, 1.000000, 0.000000, 0.000000

GOTO/POL, 76.231783, 125.228569, 11.000000

GOTO/POL, 73.498777, 125.283564, 11.000000

GOTO/POL, 70.952585, 124.493571, 11.000000

PTMEAS/POL, 65.704330, 124.801762, 11.000000, 0.000000, 1.000000, -0.000000

GOTO/POL, 69.020838, 122.909543, -39.000000

ENDMES

F(K-3) = FEAT/CIRCLE,INNER,POL, 75.0000, 240.0000, 11.0000, 0.000000,$

0.000000, -1.000000, 22.0000

$$ Measurement points are created through nominal points

MEAS/CIRCLE, F(K-3), 4

GOTO/POL, 69.011388, 122.918398, -39.993117

GOTO/POL, 71.753600, 244.851245, -39.993117

GOTO/POL, 71.753600, 244.851245, -39.000000

PTMEAS/POL, 70.149828, 247.804822, 11.000000, -1.000000, -0.000000, 0.000000

GOTO/POL, 69.571945, 243.515057, 11.000000

GOTO/POL, 68.255964, 241.522483, 11.000000

GOTO/POL, 68.059208, 239.230028, 11.000000

PTMEAS/POL, 65.704330, 235.198238, 11.000000, -0.000000, -1.000000, 0.000000

GOTO/POL, 70.952585, 235.506429, 11.000000

GOTO/POL, 73.498778, 234.716436, 11.000000

GOTO/POL, 76.231784, 234.771431, 11.000000

PTMEAS/POL, 81.061715, 233.251074, 11.000000, 1.000000, 0.000000, 0.000000

GOTO/POL, 80.671787, 236.969077, 11.000000

GOTO/POL, 81.788240, 238.729465, 11.000000

GOTO/POL, 81.952041, 240.639437, 11.000000

PTMEAS/POL, 84.705024, 243.722911, 11.000000, 0.000000, 1.000000, -0.000000

GOTO/POL, 81.143802, 242.474560, -39.000000

ENDMES

F(PROJCI4) = FEAT/CIRCLE,INNER,POL, 75, 0, 0,0,$

-0.00000, -1.000000, 22.0000

CONST/CIRCLE,F(PROJCI4),PROJCT,FA(K-1),FA(PLN4)

F(PROJCI5) = FEAT/CIRCLE,INNER,POL, 75, 120, 0, 0,$

-0.00000, -1.000000, 22.0000

CONST/CIRCLE,F(PROJCI5),PROJCT,FA(K-2),FA(PLN4)

F(PROJCI6) = FEAT/CIRCLE,INNER,POL, 75.0000, 240.0000, 0.0000, -0.0000,$

-0.00000, -1.000000, 22.0000

CONST/CIRCLE,F(PROJCI6),PROJCT,FA(K-3),FA(PLN4)

DMESW/COMAND,'D(CRD6) = LOCATE/XYDIR, ZAXIS, FA(PROJCI4), XYZAXI,$

FA(PROJCI5), XYZAXI, FA(PROJCI6), XYZAXI'

MODE/PROG,MAN

SNSET/APPRCH, 3

SNSET/RETRCT, 3

SNSET/DEPTH, 0.0000

SNSET/SEARCH, 10.0000

SNSET/CLRSRF, 50

F(L-1) = FEAT/CIRCLE,INNER,POL, 60.0000, 35.0000, 2.5000, 0.000000,$

0.000000, -1.000000, 10.0000

$$ Measurement points are created through nominal points

MEAS/CIRCLE, F(L-1), 4

GOTO/POL, 60.272503, 326.037749, -48.493117

GOTO/POL, 60.827534, 34.456002, -48.493117

GOTO/POL, 60.827534, 34.456002, -47.500000

PTMEAS/POL, 64.159897, 32.438095, 2.500000, -1.000000, -0.000000, -0.000000

PTMEAS/POL, 63.001145, 38.727487, 2.500000, -0.000000, -1.000000, 0.000000

PTMEAS/POL, 55.977743, 37.936681, 2.500000, 1.000000, 0.000000, 0.000000

PTMEAS/POL, 57.278755, 30.899514, 2.500000, 0.000000, 1.000000, -0.000000

GOTO/POL, 59.428202, 34.204778, -47.500000

ENDMES

F(L-2) = FEAT/CIRCLE,INNER,POL, 60.0000, 145.0000, 2.5000, 0.000000,$

0.000000, -1.000000, 10.0000

$$ Measurement points are created through nominal points

MEAS/CIRCLE, F(L-2), 4

GOTO/POL, 59.417037, 34.195633, -48.493117

GOTO/POL, 59.178028, 144.440835, -48.493117

GOTO/POL, 59.178028, 144.440835, -47.500000

PTMEAS/POL, 55.977755, 142.063302, 2.500000, -1.000000, -0.000000, -0.000000

PTMEAS/POL, 63.001161, 141.272525, 2.500000, -0.000000, -1.000000, 0.000000

PTMEAS/POL, 64.159885, 147.561921, 2.500000, 1.000000, 0.000000, 0.000000

PTMEAS/POL, 57.278737, 149.100475, 2.500000, 0.000000, 1.000000, -0.000000

GOTO/POL, 59.428198, 145.795220, -47.500000

ENDMES

F(L-3) = FEAT/CIRCLE,INNER,POL, 60.0000, 215.0000, 2.5000, 0.000000,$

0.000000, -1.000000, 10.0000

$$ Measurement points are created through nominal points

MEAS/CIRCLE, F(L-3), 4

GOTO/POL, 59.422848, 145.808333, -48.493117

GOTO/POL, 59.178028, 215.559165, -48.493117

GOTO/POL, 59.178028, 215.559165, -47.500000

PTMEAS/POL, 55.977755, 217.936698, 2.500000, -1.000000, -0.000000, -0.000000

PTMEAS/POL, 57.278737, 210.899524, 2.500000, -0.000000, -1.000000, 0.000000

PTMEAS/POL, 64.159885, 212.438079, 2.500000, 1.000000, 0.000000, 0.000000

PTMEAS/POL, 63.001161, 218.727475, 2.500000, 0.000000, 1.000000, -0.000000

GOTO/POL, 60.583140, 215.780059, -47.500000

ENDMES

F(L-4) = FEAT/CIRCLE,INNER,POL, 60.0000, 325.0000, 2.5000, 0.000000,$

0.000000, -1.000000, 10.0000

$$ Measurement points are created through nominal points

MEAS/CIRCLE, F(L-4), 4

GOTO/POL, 60.593217, 215.788250, -48.493117

GOTO/POL, 60.827534, 325.543998, -48.493117

GOTO/POL, 60.827534, 325.543998, -47.500000

PTMEAS/POL, 64.159897, 327.561905, 2.500000, -1.000000, -0.000000, -0.000000

PTMEAS/POL, 57.278755, 329.100486, 2.500000, -0.000000, -1.000000, 0.000000

PTMEAS/POL, 55.977743, 322.063319, 2.500000, 1.000000, 0.000000, 0.000000

PTMEAS/POL, 63.001145, 321.272513, 2.500000, 0.000000, 1.000000, -0.000000

GOTO/POL, 60.583137, 324.219938, -47.500000

ENDMES

OUTPUT/FA(L-1),TA(TCORTOL1),TA(TCORTOL2)

OUTPUT/FA(L-2),TA(TCORTOL1),TA(TCORTOL2)

OUTPUT/FA(L-3),TA(TCORTOL1),TA(TCORTOL2)

OUTPUT/FA(L-4),TA(TCORTOL1),TA(TCORTOL2)

EQUATE/DA(CRD3), DA(CRD6)

F(J-1) = FEAT/CIRCLE,INNER,POL, 75.0000, 0.0000, -3.1987, 0.001019,$

-0.000220, 0.999999, 22.0000

F(J-2) = FEAT/CIRCLE,INNER,POL, 75.0000, 120.0000, -3.3143, 0.001019,$

-0.000220, 0.999999, 22.0000

F(J-3) = FEAT/CIRCLE,INNER,POL, 75.0000, 240.0000, -3.1953, 0.001019,$

-0.000220, 0.999999, 22.0000

F(J-4) = FEAT/CIRCLE,INNER,POL, 0.0000, 0.0000, -3.2361, 0.001019,$

-0.000220, 0.999999, 50.0000

F(J-5) = FEAT/CIRCLE,INNER,POL, 43.5000, 112.0000, -3.2812, 0.001019,$

-0.000220, 0.999999, 20.0000

F(J-6) = FEAT/CIRCLE,INNER,POL, 43.5000, 292.0000, -3.1910, 0.001019,$

-0.000220, 0.999999, 20.0000

OUTPUT/FA(J-1),TA(TCORTOL1),TA(TCORTOL2)

OUTPUT/FA(J-2),TA(TCORTOL1),TA(TCORTOL2)

OUTPUT/FA(J-3),TA(TCORTOL1),TA(TCORTOL2)

OUTPUT/FA(J-4),TA(TCORTOL1),TA(TCORTOL2)

OUTPUT/FA(J-5),TA(TCORTOL1),TA(TCORTOL2)

OUTPUT/FA(J-6),TA(TCORTOL1),TA(TCORTOL2)

来源：山涧果子

RationalDMIS子程序调用

DMISMN/'Created by [山涧果子] on 星期六, 七月 15, 2017', 4.0UNITS/MM, ANGDECWKPLAN/XYPLANPRCOMP/ONTECOMP/ONFLY/1.000000MODE/PROG, MANSNSET/APPRCH, 3.000000SNSET/RETRCT, 3.000000SNSET/DEPTH, 0.000000SNSET/SEARCH, 10.000000SNSET/CLRSRF, 30.000000RECALL/D(MCS)SNSLCT/S(ROOTSN1)GEOALG/CIRCLE, LSTSQRGEOALG/ARC, LSTSQRGEOALG/PLANE, LSTSQR$$$$(MENU)DECL/COMMON,INTGR,V1,V2,V3,V4,V5,V6Lenovo = PROMPT/TITLE,'山涧果子 ',TEXT,'构建坐标系，模型对齐！',CHECK,'1',$ V1,TEXT,'测量中心大圆！',CHECK,'2',V2,TEXT,'测量均布四个小圆！',CHECK,'3',$ V3,TEXT,'测量圆键槽！',CHECK,'4',V4,TEXT,'测量点集',CHECK,'5',V5,TEXT,$ '退出（结束测量）',CHECK,'6',V6IF/(V1.EQ.1)JUMPTO/(ALIGNMENT)ELSEIF/(V2.EQ.1)JUMPTO/(SMALL_CIRCLES)ELSEIF/(V3.EQ.1)JUMPTO/(LARGE_CIRCLE)ELSEIF/(V4.EQ.1)JUMPTO/(ROUND_SLOT)ELSEIF/(V5.EQ.1)JUMPTO/(POINTS)ELSEIF/(V6.EQ.1)JUMPTO/(END)ENDIFENDIFENDIFENDIFENDIFENDIF(ALIGNMENT)MODE/MANF(PLN1) = FEAT/PLANE,CART, 32.082523, 76.014419, 62.490748, 0.000181,$ -0.000070, 1.000000$$ Measurement points are created through actual pointsMEAS/PLANE, F(PLN1), 4 PTMEAS/CART, 4.050106, 43.806519, 62.493564, 0.000181, -0.000070, 1.000000 PTMEAS/CART, 52.285087, 43.221539, 62.484785, 0.000181, -0.000070, 1.000000 PTMEAS/CART, 53.696995, 96.819366, 62.488293, 0.000181, -0.000070, 1.000000 PTMEAS/CART, 18.297903, 120.210251, 62.496349, 0.000181, -0.000070, 1.000000ENDMESOUTPUT/FA(PLN1)F(LN1) = FEAT/LINE,BND,CART, 1.957149, -0.000029, 43.501493, 42.885566,$ -0.000049, 44.036092, 0.000000, -1.000000, -0.000070$$ Measurement points are created through actual pointsMEAS/LINE, F(LN1), 2 PTMEAS/CART, 1.957149, -0.000029, 43.501493, 0.000000, -1.000000, -0.000070 PTMEAS/CART, 42.885566, -0.000049, 44.036092, 0.000000, -1.000000, -0.000070ENDMESOUTPUT/FA(LN1)F(LN2) = FEAT/LINE,BND,CART, 0.000000, 43.615447, 60.500315, 0.000000,$ 106.140746, 57.549547, -1.000000, 0.000009, 0.000181$$ Measurement points are created through actual pointsMEAS/LINE, F(LN2), 2 PTMEAS/CART, -0.000000, 43.615447, 60.500315, -1.000000, 0.000009, 0.000181 PTMEAS/CART, -0.000000, 106.140746, 57.549547, -1.000000, 0.000009, 0.000181ENDMESOUTPUT/FA(LN2)F(PT_INTER1) = FEAT/POINT,CART, 0.124329, 0.449182, 52.997723, -0.013046,$ 0.047137, 0.998803CONST/POINT, F(PT_INTER1), INTOF, FA(LN1), FA(LN2)OUTPUT/FA(PT_INTER1)D(CRD1) = DATSET/FA(PLN1), ZDIR, ZORIG, FA(LN1), XDIR, YORIG, FA(PT_INTER1),$ XORIGD(CRD1) = TRANS/ZORIG, -62.5000, YORIG, -0, XORIG, -0$$ Set.CAD2PCS.CADM_1$$ Set.CADViewCenter.CADM_1JUMPTO/(MENU)MODE/PROG,MAN(SMALL_CIRCLES)$$ MACRO: EASI_CLEARPLN_GOTO$$ FUNCTION: CLEARANCE SURFACE IMPLEMENTATION$$ Move machine CLEAR SURFACE DIST above the current clear surface $$ plane and then move machine parallel to the clear surface plane $$ ALL Macro parameters are in PCS and Current UNITS$$ Last update: 3-1-04 Add mode checking. only works in PROG MODE$$ Last update: 8-24-04 Clear position is based on the surface of$$ $$ This sample DMIS Macro is provided by External-Array Software, Inc.$$ It should be modified for your own use. There is no guarantee for$$ the quality of this Macro. November, 2003M(EASI_CLEARPLN_GOTO) = MACRO/ISNOM, TARX, TARY, TARZ DECL/LOCAL, REAL, CCX, CCY, CCZ, CCI, CCJ, CCK DECL/LOCAL, REAL, CURX, CURY, CURZ, TD, CLRDIST, SDIAM DECL/LOCAL, CHAR, 255, CLRLABEL, FLABEL, MMODE, SNAME MMODE = VALUE/MODE CLRLABEL = VALUE/SNSET, CLRSRF IF/ ( (LEN(CLRLABEL) .GT. 0) .AND. (MMODE .EQ. 'PROG,MAN') ) CLRDIST = VALUE/SNSET, CLRSRF, DIST FLABEL = ASSIGN/'FA' IF/ ISNOM .EQ. 0 FLABEL = ASSIGN/'F' ENDIF CCX = OBTAIN/FLABEL(@CLRLABEL), 3 CCY = OBTAIN/FLABEL(@CLRLABEL), 4 CCZ = OBTAIN/FLABEL(@CLRLABEL), 5 CCI = OBTAIN/FLABEL(@CLRLABEL), 6 CCJ = OBTAIN/FLABEL(@CLRLABEL), 7 CCK = OBTAIN/FLABEL(@CLRLABEL), 8 SNAME = VALUE/SNSLCT SDIAM = OBTAIN/SS(SNAME), 8 CCX = ASSIGN/CCX + CCI * SDIAM/2 CCY = ASSIGN/CCY + CCJ * SDIAM/2 CCZ = ASSIGN/CCZ + CCK * SDIAM/2 CURX = VALUE/GOTO, XAXIS CURY = VALUE/GOTO, YAXIS CURZ = VALUE/GOTO, ZAXIS TD = ASSIGN/(CURX - CCX) * CCI + (CURY - CCY) * CCJ + (CURZ - CCZ) * CCK IF/ TD .LT. CLRDIST TD = ASSIGN/(CLRDIST - TD) GOTO/CURX+CCI*TD, CURY+CCJ*TD, CURZ+CCK*TD ENDIF TD = ASSIGN/(TARX - CCX) * CCI + (TARY - CCY) * CCJ + (TARZ - CCZ) * CCK IF/ TD .LT. CLRDIST TD = ASSIGN/(CLRDIST - TD) GOTO/TARX+CCI*TD, TARY+CCJ*TD, TARZ+CCK*TD ENDIF ENDIF ENDMACSNSET/APPRCH, 3.0000SNSET/RETRCT, 3.0000SNSET/DEPTH, 0.0000SNSET/SEARCH, 10.0000SNSET/CLRSRF, F(PLN1), 30.0000F(SMALL_CIRCLES) = FEAT/CIRCLE,INNER,CART, 29.629035, 95.494885, 62.485214,$ 0.000357, -0.000101, 1.000000, 25.391735$$ Measurement points are created through nominal points$$ CALL/M(EASI_CLEARPLN_GOTO), 0, -4.993488, 106.138230, 93.499581MEAS/CIRCLE, F(SMALL_CIRCLES), 4 GOTO/CART, -4.993488, 106.138230, 93.499581 GOTO/CART, 38.335798, 95.491789, 93.490984 GOTO/CART, 38.335615, 95.491860, 92.482107 PTMEAS/CART, 42.324902, 95.494886, 62.480681, -1.000000, 0.000000, 0.000400 GOTO/CART, 37.662968, 92.167121, 62.482010 GOTO/CART, 35.777942, 89.345979, 62.482398 GOTO/CART, 32.956799, 87.460951, 62.483216 PTMEAS/CART, 29.629035, 82.799018, 62.483934, 0.000000, 1.000000, 0.000100 GOTO/CART, 26.301271, 87.460951, 62.485592 GOTO/CART, 23.480129, 89.345978, 62.486790 GOTO/CART, 21.595101, 92.167120, 62.487748 PTMEAS/CART, 16.933168, 95.494884, 62.489748, 1.000000, 0.000000, -0.000400 GOTO/CART, 21.595101, 98.822649, 62.488419 GOTO/CART, 23.480128, 101.643791, 62.488030 GOTO/CART, 26.301270, 103.528819, 62.487213 PTMEAS/CART, 29.629034, 108.190752, 62.486495, 0.000000, -1.000000, -0.000100 GOTO/CART, 29.639748, 104.187727, 92.486089ENDMESOUTPUT/FA(SMALL_CIRCLES)JUMPTO/(MENU)(LARGE_CIRCLE)SNSET/APPRCH, 3.0000SNSET/RETRCT, 3.0000SNSET/DEPTH, 0.0000SNSET/SEARCH, 10.0000SNSET/CLRSRF, F(PLN1), 30.0000F(LARGE_CIRCLE1) = FEAT/CIRCLE,INNER,CART, 47.599750, 77.533498, 62.483527,$ -0.001170, -0.000997, 0.999999, 9.526483$$ Measurement points are created through nominal points$$ CALL/M(EASI_CLEARPLN_GOTO), 0, 29.639930, 104.187656, 93.493170MEAS/CIRCLE, F(LARGE_CIRCLE1), 4 GOTO/CART, 29.639930, 104.187656, 93.493170 GOTO/CART, 48.328065, 77.503514, 93.487910 GOTO/CART, 48.327883, 77.503584, 92.484385 PTMEAS/CART, 52.362988, 77.533493, 62.489101, -0.999999, 0.000000, -0.001200 PTMEAS/CART, 47.599751, 72.770259, 62.478778, 0.000000, 1.000000, 0.001000 PTMEAS/CART, 42.836512, 77.533503, 62.477953, 0.999999, 0.000000, 0.001200 PTMEAS/CART, 47.599749, 82.296737, 62.488276, 0.000000, -1.000000, -0.001000 GOTO/CART, 47.564642, 78.266826, 92.484253ENDMESOUTPUT/FA(LARGE_CIRCLE1)F(LARGE_CIRCLE2) = FEAT/CIRCLE,INNER,CART, 47.591675, 113.457218, 62.483108,$ 0.000715, -0.001658, 0.999998, 9.521386$$ Measurement points are created through nominal points$$ CALL/M(EASI_CLEARPLN_GOTO), 0, 47.564824, 78.266755, 93.488102MEAS/CIRCLE, F(LARGE_CIRCLE2), 4 GOTO/CART, 47.564824, 78.266755, 93.488102 GOTO/CART, 48.374009, 113.407395, 93.490424 GOTO/CART, 48.373827, 113.407466, 92.482515 PTMEAS/CART, 52.352367, 113.457224, 62.479703, -1.000000, 0.000000, 0.000700 PTMEAS/CART, 47.591676, 108.696532, 62.475213, 0.000000, 0.999999, 0.001700 PTMEAS/CART, 42.830983, 113.457212, 62.486513, 1.000000, 0.000000, -0.000700 PTMEAS/CART, 47.591675, 118.217904, 62.491003, 0.000000, -0.999999, -0.001700 GOTO/CART, 47.613134, 114.168157, 92.484320ENDMESOUTPUT/FA(LARGE_CIRCLE2)F(LARGE_CIRCLE3) = FEAT/CIRCLE,INNER,CART, 11.672732, 113.459471, 62.495001,$ 0.000610, -0.000461, 1.000000, 9.517758$$ Measurement points are created through nominal points$$ CALL/M(EASI_CLEARPLN_GOTO), 0, 47.613316, 114.168086, 93.490615MEAS/CIRCLE, F(LARGE_CIRCLE3), 4 GOTO/CART, 47.613316, 114.168086, 93.490615 GOTO/CART, 12.450083, 113.445569, 93.496934 GOTO/CART, 12.449902, 113.445639, 92.494530 PTMEAS/CART, 16.431610, 113.459472, 62.492100, -1.000000, 0.000000, 0.000600 PTMEAS/CART, 11.672732, 108.700593, 62.492807, 0.000000, 1.000000, 0.000500 PTMEAS/CART, 6.913854, 113.459470, 62.497903, 1.000000, 0.000000, -0.000600 PTMEAS/CART, 11.672733, 118.218349, 62.497196, -0.000000, -1.000000,$ -0.000500 GOTO/CART, 11.691023, 114.204518, 92.495343ENDMESOUTPUT/FA(LARGE_CIRCLE3)F(LARGE_CIRCLE4) = FEAT/CIRCLE,INNER,CART, 11.664848, 77.534322, 62.489405,$ 0.000340, -0.000125, 1.000000, 9.511912$$ Measurement points are created through nominal points$$ CALL/M(EASI_CLEARPLN_GOTO), 0, 11.691204, 114.204448, 93.497125MEAS/CIRCLE, F(LARGE_CIRCLE4), 4 GOTO/CART, 11.691204, 114.204448, 93.497125 GOTO/CART, 12.431179, 77.530504, 93.494415 GOTO/CART, 12.430997, 77.530575, 92.489146 PTMEAS/CART, 16.420804, 77.534322, 62.487789, -1.000000, 0.000000, 0.000300 PTMEAS/CART, 11.664848, 72.778366, 62.488811, 0.000000, 1.000000, 0.000100 PTMEAS/CART, 6.908893, 77.534322, 62.491021, 1.000000, 0.000000, -0.000300 PTMEAS/CART, 11.664849, 82.290278, 62.489999, -0.000000, -1.000000, -0.000100 GOTO/CART, 11.675041, 78.286531, 92.489498ENDMESOUTPUT/FA(LARGE_CIRCLE4)JUMPTO/(MENU)(ROUND_SLOT)SNSET/APPRCH, 3.0000SNSET/RETRCT, 3.0000SNSET/DEPTH, 0.0000SNSET/SEARCH, 10.0000SNSET/CLRSRF, F(PLN1), 30.0000F(SLT1) = FEAT/CPARLN,INNER,ROUND,CART, 30.052095, 54.653468, 62.480866,$ 0.000308, -0.000098, 1.000000, 0.999991, 0.004228, -0.000307, 50.125917,$ 12.769768$$ Measurement points are created through nominal points$$ CALL/M(EASI_CLEARPLN_GOTO), 0, 11.675223, 78.286460, 93.494605MEAS/CPARLN, F(SLT1), 6 GOTO/CART, 11.675223, 78.286460, 93.494605 GOTO/CART, 39.382356, 58.075626, 93.488166 PTMEAS/CART, 39.364055, 61.077777, 62.478631, 0.004200, -0.999991, -0.000100 PTMEAS/CART, 20.686148, 60.998812, 62.484374, 0.004200, -0.999991, -0.000100 PTMEAS/CART, 4.989361, 54.547509, 62.488572, 0.999991, 0.004200, -0.000300 PTMEAS/CART, 20.740134, 48.229158, 62.483101, -0.004200, 0.999991, 0.000100 PTMEAS/CART, 39.418042, 48.308123, 62.477358, -0.004200, 0.999991, 0.000100 PTMEAS/CART, 55.114828, 54.759426, 62.473160, -0.999991, -0.004200, 0.000300ENDMESOUTPUT/FA(SLT1)JUMPTO/(MENU)(POINTS)SNSET/APPRCH, 3.0000SNSET/RETRCT, 3.0000SNSET/DEPTH, 0.0000SNSET/SEARCH, 10.0000SNSET/CLRSRF, F(PLN1), 30.0000F(PT1) = FEAT/POINT,CART, 19.685307, 16.177397, 62.488791, 0.000181,$ -0.000070, 1.000000$$ CALL/M(EASI_CLEARPLN_GOTO), 0, 19.686031, 16.177116, 66.488791MEAS/POINT, F(PT1), 1 GOTO/CART, 19.690922, 16.175219, 93.488791 PTMEAS/CART, 19.685307, 16.177397, 62.488791, 0.000181, -0.000070, 1.000000ENDMESF(PT2) = FEAT/POINT,CART, 5.136687, 44.584263, 62.486866, 0.000362,$ -0.000140, 1.000000$$ CALL/M(EASI_CLEARPLN_GOTO), 0, 5.138136, 44.583701, 66.486866MEAS/POINT, F(PT2), 1 GOTO/CART, 5.143029, 44.581804, 93.493421 PTMEAS/CART, 5.136687, 44.584263, 62.486866, 0.000362, -0.000140, 1.000000ENDMESF(PT3) = FEAT/POINT,CART, 51.539172, 44.140194, 62.469991, 0.000362,$ -0.000140, 1.000000$$ CALL/M(EASI_CLEARPLN_GOTO), 0, 51.540621, 44.139633, 66.469991MEAS/POINT, F(PT3), 1 GOTO/CART, 51.545515, 44.137735, 93.484984 PTMEAS/CART, 51.539172, 44.140194, 62.469991, 0.000362, -0.000140, 1.000000ENDMESF(PT4) = FEAT/POINT,CART, 52.484192, 87.793770, 62.475781, 0.000362,$ -0.000140, 1.000000$$ CALL/M(EASI_CLEARPLN_GOTO), 0, 52.485641, 87.793208, 66.475781MEAS/POINT, F(PT4), 1 GOTO/CART, 52.490534, 87.791311, 93.487879 PTMEAS/CART, 52.484192, 87.793770, 62.475781, 0.000362, -0.000140, 1.000000ENDMESF(PT5) = FEAT/POINT,CART, 36.424607, 116.441673, 62.485624, 0.000362,$ -0.000140, 1.000000$$ CALL/M(EASI_CLEARPLN_GOTO), 0, 36.426056, 116.441111, 66.485623MEAS/POINT, F(PT5), 1 GOTO/CART, 36.430948, 116.439214, 93.492800 PTMEAS/CART, 36.424607, 116.441673, 62.485624, 0.000362, -0.000140, 1.000000ENDMESF(PT6) = FEAT/POINT,CART, 9.062191, 95.266464, 62.492563, 0.000362,$ -0.000140, 1.000000$$ CALL/M(EASI_CLEARPLN_GOTO), 0, 9.063640, 95.265902, 66.492563MEAS/POINT, F(PT6), 1 GOTO/CART, 9.068532, 95.264006, 93.496270 PTMEAS/CART, 9.062191, 95.266464, 62.492563, 0.000362, -0.000140, 1.000000ENDMESF(PT7) = FEAT/POINT,CART, 30.077091, 70.954735, 62.481534, 0.000362,$ -0.000140, 1.000000$$ CALL/M(EASI_CLEARPLN_GOTO), 0, 30.078540, 70.954173, 66.481534MEAS/POINT, F(PT7), 1 GOTO/CART, 30.083433, 70.952276, 93.490755 PTMEAS/CART, 30.077091, 70.954735, 62.481534, 0.000362, -0.000140, 1.000000ENDMESF(PT8) = FEAT/POINT,CART, 25.303820, 116.631279, 62.489680, 0.000362,$ -0.000140, 1.000000$$ CALL/M(EASI_CLEARPLN_GOTO), 0, 25.305269, 116.630717, 66.489679MEAS/POINT, F(PT8), 1 GOTO/CART, 25.310161, 116.628820, 93.494828 PTMEAS/CART, 25.303820, 116.631279, 62.489680, 0.000362, -0.000140, 1.000000ENDMESJUMPTO/(MENU)(END)来源：山涧果子