首页/文章/ 详情

【新文速递】2023年10月30日复合材料SCI期刊最新文章

13天前浏览423

今日更新:Composite Structures 3 篇,Composites Science and Technology 2 篇

Composite Structures

Investigating the Effect of Cure Schedules and Cure Initiators on Sustainable Composites for Large Offshore Structures

Pothnis J.R., Vélon K., Bhatia G.S., Hejjaji A., Comer A.J.

doi:10.1016/j.compstruct.2023.117648

 

研究固化时间表和固化引发剂对大型近海结构可持续复合材料的影响

This study evaluates the effect of post-cure schedules and cure initiator form on the mechanical properties of Glass fibre reinforced polymer (GFRP) laminates manufactured using an infusible reactive thermoplastic resin. Tensile, flexural, shear and dynamic mechanical analysis tests were conducted. Fractography was also performed. Specimens fabricated using liquid cure initiator and subjected to an elevated temperature post-cure were the control specimens. Ambient cured specimens decreased by no more than 12% in the case of tensile properties (modulus of 90° specimens) and by < 14.3% in the case of flexural properties (also modulus in 90° specimens). Furthermore, the difference in mechanical properties of 0° specimens fabricated using a powder cure initiator was observed to be within ≈ 7% of respective properties of control specimens. In the context of fabricating thick laminates for large-size offshore structures, the results suggest that an extended ambient post-cure cycle in conjunction with an initiator in powder form can be employed instead of an elevated temperature post-cure schedule with initiator in liquid form. This is economically beneficial since it eliminates infrastructure required for elevated temperature curing/post-curing. The risk of porosity induced due to liquid-based initiators is also avoided.

本研究评估了后固化时间和固化引发剂形式对使用可浸润反应性热塑性树脂制造的玻璃纤维增强聚合物(GFRP)层压板机械性能的影响。研究进行了拉伸、弯曲、剪切和动态机械分析测试。此外,还进行了碎裂分析。使用液态固化引发剂制造的试样和固化后的高温试样为对照试样。常温固化试样的拉伸性能(90° 试样的模量)下降不超过 12%,弯曲性能(90° 试样的模量)下降小于 14.3%。此外,还观察到使用粉末固化引发剂制作的 0° 试样的机械性能与对照试样各自性能的差异在 ≈ 7% 以内。结果表明,在为大型海上结构制造厚层压板时,可以采用延长的环境后固化周期和粉末状引发剂,而不是采用液态引发剂的高温后固化计划。这在经济上是有利的,因为它省去了高温固化/后固化所需的基础设施。此外,还可避免液态引发剂引起的气孔风险。


The effect of load concentration on one-way response of 3D-woven sandwich panels

Mirsalehi Maryam, Kianpour Kiarash, Shahbeyk Sharif, Bakhshi Mohammad

doi:10.1016/j.compstruct.2023.117659

荷载集中对三维编织夹芯板单向响应的影响

As a relatively new class of load bearing elements, 3D-woven sandwich panels (3DWSPs) are emerging in many engineering applications. Similar to other structural elements, the practical usage of the 3DWSPs requires deep understanding around their mechanical properties like elastic stiffness and failure strength. The present study investigates the effect of load concentration on one-way response of the 3DWSPs by: (1) running a comprehensive set of 64 tests to find out the influence of various interfering parameters such as loading span length, the thickness of loaded skin, the shape of loading bar, and panel’s direction, (2) thoughtful interpretation of the elastic and failure results, (3) generation of failure maps, and (4) development of reliable theoretical models for the linear elastic response and the four observed failure mechanisms of skin indentation, skin wrinkling, core shear collapse, and interpillar skin buckling.

作为一类相对较新的承重元件,三维编织夹芯板(3DWSP)正在许多工程应用中崭露头角。与其他结构元件类似,3DWSP 的实际应用需要深入了解其机械特性,如弹性刚度和破坏强度。本研究通过以下方法研究荷载集中对 3DWSP 单向响应的影响:(1)进行 64 项综合测试,以找出加载跨度长度、加载表皮厚度、加载杆形状和面板方向等各种干扰参数的影响;(2)对弹性和破坏结果进行周到的解释;(3)生成破坏图;(4)为线性弹性响应以及表皮压痕、表皮起皱、核心剪切塌陷和柱间表皮屈曲这四种观察到的破坏机制建立可靠的理论模型。


Application of Elastic Metamaterials/Meta-structures in Civil Engineering: A Review

Contreras Nicolás, Zhang Xihong, Hao Hong, Hernández Francisco

doi:10.1016/j.compstruct.2023.117663

弹性超材料/超结构在土木工程中的应用:综述

Inspired by sonic engineering, locally resonant metamaterials have attracted much attention from researchers in civil engineering for their unique characteristics of stress wave attenuation and vibration control capacities. This paper presents a comprehensive review of the latest progress of locally resonant metamaterials and their potential applications in civil engineering for structure protection against dynamic loads. The concepts of metamaterials for stress wave attenuation are introduced first, followed by a comprehensive overview of the historical origins and development of metamaterials. Existing analytical approaches for metamaterials, including theoretical solutions, numerical simulations, and experimental examinations, are summarised. Commonly used meta-structures with internal or external resonators and their applications are reviewed and discussed. Research gaps and future outlooks are also identified and briefed.

受声波工程学的启发,局部谐振超材料因其独特的应力波衰减特性和振动控制能力而备受土木工程研究人员的关注。本文全面综述了局部谐振超材料的最新进展及其在土木工程中用于动态载荷结构保护的潜在应用。首先介绍了用于应力波衰减的超材料概念,然后全面概述了超材料的历史起源和发展。总结了现有的超材料分析方法,包括理论求解、数值模拟和实验检验。回顾并讨论了带有内部或外部谐振器的常用超材料结构及其应用。此外,还确定并简要介绍了研究差距和未来展望。


Composites Science and Technology

A new integrated modeling method for predicting low-velocity impact behavior and residual tensile failure of Z-pinned T-joints

Zhou Jianwu, Zhao Zhibin, Jia Liyong, Zhang Chao

doi:10.1016/j.compscitech.2023.110316

 

预测 Z 销 T 型接头低速冲击行为和残余拉伸失效的新型综合建模方法

Composite T-joints are highly susceptible to low-velocity impact, which can significantly affect their residual performance due to the primary working condition of bearing out-of-plane tensile loads. Currently, most methods that employ multiple models or analytical steps to sequentially assess the mechanical properties of composites generally exhibit certain limitations, leaving room for improvement. This study has developed a finite element (FE) model to simulate the low-velocity impact and post-impact tensile behaviors of carbon fiber reinforced polymers (CFRP) T-joints using an integrated analysis method. The model is based on stress failure criteria and continuous stiffness degradation theory and incorporates corrections to the damage variables. Both the low-velocity impact and quasi-static tensile portions of the model are implemented using an explicit solver with the VUMAT subroutine for calculations in Abaqus. The element damage states are transferred between the two models via a Python script, mitigating the inefficiencies and uncontrollable errors associated with the traditional method of transferring element information between multiple models or analytical steps. Finally, the numerical results of mechanical response and damage states are compared with experimental findings from various perspectives, and the bridging mechanism of Z-pins is thoroughly investigated. The results show that the model exhibits a maximum error of 10.41 % in the main key parameters during low-velocity impact and a maximum error of 10.30 % in the ultimate load during post-impact tension. The model's delamination damage state and final tensile failure mode closely align with the experimental results. Furthermore, a comprehensive analysis of the FE model indicates that the pull-out force of the Z-pin is unrelated to its implantation position or pull-out rate, and the reinforcing effect of the Z-pin becomes significantly apparent only after the CFRP T-joint reaches a certain degree of initial damage.

复合材料 T 型接头极易受到低速冲击,由于其主要工作条件是承受平面外拉伸载荷,这可能会严重影响其剩余性能。目前,大多数采用多种模型或分析步骤依次评估复合材料机械性能的方法普遍存在一定的局限性,有待改进。本研究开发了一种有限元(FE)模型,利用综合分析方法模拟碳纤维增强聚合物(CFRP)T 型接头的低速冲击和冲击后拉伸行为。该模型基于应力失效标准和连续刚度退化理论,并结合了对损伤变量的修正。该模型的低速冲击和准静态拉伸部分均采用显式求解器和 VUMAT 子程序在 Abaqus 中进行计算。元素损伤状态通过 Python 脚本在两个模型之间传输,从而减少了在多个模型或分析步骤之间传输元素信息的传统方法所带来的低效率和不可控误差。最后,从不同角度将机械响应和损伤状态的数值结果与实验结果进行了比较,并深入研究了 Z 销的桥接机制。结果表明,该模型在低速冲击时主要关键参数的最大误差为 10.41%,在冲击后拉伸时极限载荷的最大误差为 10.30%。模型的分层破坏状态和最终拉伸破坏模式与实验结果非常吻合。此外,对 FE 模型的综合分析表明,Z 形销的拔出力与其植入位置或拔出率无关,只有在 CFRP T 形接头达到一定的初始损坏程度后,Z 形销的加固作用才会显著显现。


Rapid and scalable synthesis of novel carboxylated aramid nanofibers for simultaneously improving the strength and toughness of carbon fiber/epoxy laminates

Yu Boshi, Wang Weitao, Zhou Guodong, Song Yihu, Peng Mao

doi:10.1016/j.compscitech.2023.110320

 

快速、可扩展地合成新型羧基芳纶纳米纤维,以同时提高碳纤维/环氧层压板的强度和韧性

Carbon fiber reinforced composites (CFRCs) are widely used in the aviation, aerospace and automotive industries. The modification of CFRCs with nanomaterials has attracted extensive research interests in recent years. Herein, we report the preparation of novel carboxylated aramid nanofibers (cANFs) by polymerization induced self-assembly, i.e. polycondensation of para-phenylenediamine with terephthaloyl chloride in the presence of a polyamide acid as both a dispersant and surface modifier, for the modification of epoxy resin and CFRCs. cANFs effectively improve the mechanical properties of epoxy resin, and after being sprayed onto CF fabrics, greatly improve the mechanical properties of CFRCs. With the addition of only 0.42 mg/cm2 of cANFs on each CF sheets, storage modulus, flexural strength, flexural modulus and total energy dissipation are enhanced by 27 %, 51 %, 29 % and 67 %, respectively; interlaminar shear strength (ILSS) and Mode II interlayer fracture toughness (G_IIC) are improved by 24 % and 74 %, respectively. cANFs can be comparable or even superior to most previously reported carbon nanomaterials in improving flexural strength and ILSS; and exceed most previously reported electrospun nanofibrous mats in increasing G_IIC. This study provides a new method for the rapid synthesis of functionalized ANFs to simultaneously increase the flexural properties and interlayer properties of CFRCs.

碳纤维增强复合材料(CFRC)广泛应用于航空、航天和汽车行业。近年来,纳米材料对碳纤维增强复合材料的改性引起了广泛的研究兴趣。在此,我们报告了通过聚合诱导自组装(即对苯二胺与对苯二甲酰氯在聚酰胺酸作为分散剂和表面改性剂存在的情况下缩聚)制备新型羧基芳纶纳米纤维(cANFs),用于环氧树脂和 CFRC 的改性。cANFs 可有效改善环氧树脂的机械性能,喷涂到 CF 织物上后可大大改善 CFRC 的机械性能。在每块 CF 片材上仅添加 0.42 mg/cm2 的 cANFs,就能使储能模量、抗弯强度、抗弯模量和总能量耗散分别提高 27%、51%、29% 和 67%;层间剪切强度(ILSS)和模式 II 层间断裂韧性(G_IIC)分别提高 24% 和 74%。cANFs 在提高抗弯强度和 ILSS 方面可与之前报道的大多数碳纳米材料相媲美,甚至更胜一筹;在提高 G_IIC 方面超过了之前报道的大多数电纺纳米纤维毡。这项研究为快速合成功能化 ANFs 提供了一种新方法,可同时提高 CFRC 的抗弯性能和层间性能。



来源:复合材料力学仿真Composites FEM
ACTMechanicalInspireAbaqusSTEPS振动断裂复合材料航空航天汽车理论材料储能控制
著作权归作者所有,欢迎分享,未经许可,不得转载
首次发布时间:2024-11-03
最近编辑:13天前
Tansu
签名征集中
获赞 3粉丝 0文章 503课程 0
点赞
收藏
作者推荐

【新文速递】2023年10月17日复合材料SCI期刊最新文章

今日更新:Composites Part A: Applied Science and Manufacturing 1 篇,Composites Part B: Engineering 2 篇,Composites Science and Technology 1 篇Composites Part A: Applied Science and ManufacturingExceptional dynamic compressive properties of bio-inspired three-dimensional interlocking graphene network reinforced copper matrix compositesLi Bowen, Lin Dong, Zhang Xiang, Zhao Dongdong, He Chunnian, Zhao Naiqindoi:10.1016/j.compositesa.2023.107856 受生物启发的三维交错石墨烯网络增强铜基复合材料的卓越动态抗压性能Insights into the reinforcement spatial architectures and their fundamental effects on the dynamic mechanical behaviors are of great importance for designing shock-resistant metallic structures. In this study, we report copper matrix composites (CMCs) reinforced by three-dimensional interlocking graphene network (3D-IGN) with a unique bio-inspired “brick-bridge-mortar” structure. Our results demonstrate that the 3D-IGN/Cu shows simultaneously enhanced dynamic strength and ductility as compared to the uniformly-distributed RGO/Cu and pure Cu at the specific strain rate from 1000 s-1 to 8000 s-1. The interlocking network structure not only blocks dislocation movement and restricts grain boundary sliding, but also alleviates the heat-induced softening by improving the thermal conductivity in the horizontal direction. The finite element simulation results further confirm the important role of the graphene network on strain delocalization. This work offers a promising bottom-up tactic to fabricate CMCs with network architecture and superior dynamic properties for high-rate applications.深入了解增强空间结构及其对动态力学行为的基本影响,对于设计抗冲击金属结构具有重要意义。在本研究中,我们报告了由三维交错石墨烯网络(3D-IGN)加固的铜基复合材料(CMC),该网络具有独特的生物启发 &quot;砖桥-砂浆 &quot;结构。我们的研究结果表明,与均匀分布的 RGO/Cu 和纯铜相比,在 1000 s-1 到 8000 s-1 的特定应变速率下,3D-IGN/Cu 同时显示出更高的动态强度和延展性。交错网络结构不仅阻止了位错运动,限制了晶界滑动,还通过提高水平方向的热传导率减轻了热致软化。有限元模拟结果进一步证实了石墨烯网络对应变分散的重要作用。这项研究为制造具有网络结构和优异动态特性的 CMC 提供了一种自下而上的可行方法,可用于高速率应用。Composites Part B: EngineeringMoisture diffusion and tensile properties of epoxy-based and polyurethane-based flax-glass hybrid FRP under hygrothermal and weathering environmentsHuang Silu, Yan Libo, Kasal Bohumil, Wei Yangdoi:10.1016/j.compositesb.2023.111049环氧基和聚氨酯基亚麻-玻璃混合玻璃钢在湿热和风化环境下的湿气扩散和拉伸性能This research presents tensile modulus and strength of flax-glass hybrid FRP (HFRP) flat coupons with different fibre volume fractions and fabric stacking sequences under constant hygrothermal (50 °C and 95% RH) and cyclic weathering (water spray-ultraviolet radiation) environments for six months. Two types of polymer (i.e., epoxy (EP) and polyurethane (PUR)) were employed in HFRP. Fourier transformed infrared spectroscopy (FTIR) was performed to identify the changes in functional groups of flax fibres and polymer matrix after exposures. The glass transition temperature (Tg) of polymer matrix was measured by differential scanning calorimetry (DSC), which was used to study the influence of environmental exposure on Tg. The 3D diffusion coefficients of EP-based flax FRP and glass FRP laminates were determined based on experimental moisture uptake and Fick&#39;s law. A coupled mass diffusion-stress analysis based on finite element (FE) model was conducted to simulate the moisture diffusion and swelling behaviour of HFRP. The results showed that hygrothermal and weathering exposures hardly affected tensile modulus of HFRP regardless of the matrix type. After the environmental exposure, EP-based HFRP experienced lower retention ratio of tensile strength (65.4–88.0%) compared to PUR-based HFRP (80.7–94.1%) because of higher moisture absorption in the EP-based HFRP. The influence of fabric stacking sequence on tensile strength reduction varied with different fibre volume fractions in EP-based HFRP, which was explained by the combined effects of the internal stress and damage propagation at flax-glass interface.本研究介绍了在恒定湿热(50 °C,95% RH)和循环风化(水雾-紫外线辐射)环境下,不同纤维体积分数和织物堆叠顺序的亚麻-玻璃混合玻璃纤维增强塑料(HFRP)平板的拉伸模量和强度,为期六个月。高频纤维增强塑料采用了两种聚合物(即环氧树脂(EP)和聚氨酯(PUR))。傅立叶变换红外光谱(FTIR)用于确定亚麻纤维和聚合物基体在暴露后的官能团变化。玻璃化温度(Tg)通过差示扫描量热法(DSC)测量了聚合物基体的 Tg 值,并利用该方法研究了环境暴露对聚合物基体的影响。根据实验吸湿量和菲克定律确定了 EP 基亚麻玻璃钢和玻璃钢层压板的三维扩散系数。在有限元(FE)模型的基础上进行了质量扩散-应力耦合分析,以模拟 HFRP 的水分扩散和膨胀行为。结果表明,无论基体类型如何,湿热暴露和风化暴露几乎不会影响 HFRP 的拉伸模量。环境暴露后,EP 基高频增强塑料的拉伸强度保持率(65.4-88.0%)低于 PUR 基高频增强塑料(80.7-94.1%),原因是 EP 基高频增强塑料的吸湿率较高。在 EP 基高频增强塑料中,织物堆叠顺序对拉伸强度降低的影响随纤维体积分数的不同而变化,其原因是亚麻-玻璃界面的内应力和损伤扩展的综合影响。Transforming diapers into inorganic carbonate enriched Carbon catalyst for improved trimethoprim degradation performanceLee Ye Bin, Narendra Kumar Alam Venugopal, Shin Won Sikdoi:10.1016/j.compositesb.2023.111051 将尿布转化为富含无机碳酸盐的碳催化剂,提高三甲氧苄啶的降解性能Waste-derived carbon materials are gaining popularity in persulfate/peroxymonosulfate activated water remediation process. In the present study, a carbon catalyst was prepared from baby diaper through simple pyrolysis step, and its catalytic activity was assessed through PMS activated trimethoprim (TMP) degradation. X-ray diffraction and Fourier-transform infrared spectroscopic characterization results revealed that the synthesized carbon material is complemented with sodium carbonate inorganic salt. The catalyst derived from diaper exhibits two important characteristics that make it practically applicable. Firstly, it has a high efficiency for removing TMP, and secondly, it maintains an ecological pH (7.5) level even after undergoing oxidation. Electron spin resonance and scavenging studies showed singlet oxygen was the predominant reactive oxygen species in the system. As a result, the system exhibited high tolerance to commonly found inorganic anions in the water bodies. These features make the diaper derived carbon catalysts a promising candidate for the degradation of TMP from wastewater, also providing an alternative solution for mitigating pollution of diapers in landfills.废物衍生碳材料在过硫酸盐/过硫酸盐活化水修复过程中越来越受欢迎。本研究以婴儿尿布为原料,通过简单的热解步骤制备了一种碳催化剂,并通过 PMS 活性三甲氧苄啶(TMP)降解评估了其催化活性。X 射线衍射和傅立叶变换红外光谱表征结果表明,合成的碳材料中添加了碳酸钠无机盐。从尿布中提取的催化剂具有两个重要特点,使其具有实用性。首先,它具有很高的 TMP 去除效率;其次,即使在氧化过程中,它也能保持生态 pH 值(7.5)。电子自旋共振和清除研究表明,单线态氧是该系统中最主要的活性氧。因此,该系统对水体中常见的无机阴离子具有很强的耐受性。这些特点使纸尿裤衍生碳催化剂成为降解废水中三羟甲基丙烷的理想候选物质,同时也为减轻垃圾填埋场中纸尿裤的污染提供了一种替代解决方案。Composites Science and TechnologyAn ingenious composite microstructure of mantis shrimp appendage for improving impact resistanceYang Xiao, Wang Ming, Bai Pucun, Niu Shichao, Song Honglie, Ni Jing, Shao Chun, Cao Xuweidoi:10.1016/j.compscitech.2023.110310 一种巧妙的螳螂虾附肢复合微结构可提高抗冲击性Mantis shrimp appendage, as an important weapon for hunting, have remarkable impact resistance due to their unique microstructure. In this study, the appendages were subjected to falling ball impact tests and their fracture surfaces were observed by scanning electron microscopy. It was observed that the outer layer was prone to brittle fracture, while the inner layer was more flexible and turned the brittle fracture into a ductile fracture. Our study supported the idea that the unique microstructures in the appendages act as barriers against crack growth and therefore play a leading role in the toughening of the entire appendage structure. Based on the bionic inspiration of the appendage microstructure, a bionic composite structure was designed, which consists of a rigid outer layer and a flexible inner layer. The fibers in the flexible layer show a longitudinal and sinusoidal arrangement to provide shielding to the crack tip when the fracture occurs. The toughening mechanism of the microstructure was further corroborated through finite element simulations, which demonstrated that the longitudinal arrangement of fibers played a pivotal role in spreading stress concentration and thereby delaying the fracture process. The sinusoidal arrangement of fibers was also found to be instrumental in not only bridging the rigid and flexible layers, but also in directing the deviation of the crack path. This work was enlightening for the structural design of impact-resistant composites.螳螂虾附肢是一种重要的狩猎武器,因其独特的微观结构而具有显著的抗冲击性。本研究对附肢进行了落球冲击试验,并利用扫描电子显微镜对其断裂面进行了观察。结果表明,外层容易发生脆性断裂,而内层则更具弹性,可将脆性断裂转化为韧性断裂。我们的研究支持了这一观点,即附肢中独特的微结构是阻止裂纹生长的屏障,因此在整个附肢结构的增韧过程中起着主导作用。根据附肢微结构的仿生灵感,我们设计了一种仿生复合结构,它由刚性外层和柔性内层组成。柔性层中的纤维呈纵向正弦排列,在发生断裂时对裂纹尖端起到屏蔽作用。有限元模拟进一步证实了微结构的增韧机理,证明纤维的纵向排列在分散应力集中从而延缓断裂过程中发挥了关键作用。研究还发现,纤维的正弦排列不仅有助于连接刚性层和柔性层,还能引导裂纹路径的偏离。这项研究对抗冲击复合材料的结构设计具有启发意义。来源:复合材料力学仿真Composites FEM

未登录
还没有评论
课程
培训
服务
行家
VIP会员 学习 福利任务 兑换礼品
下载APP
联系我们
帮助与反馈