首页/文章/ 详情

【新文速递】2024年4月13日固体力学SCI期刊最新文章

19天前浏览329

 

今日更新:International Journal of Solids and Structures 2 篇,International Journal of Plasticity 3 篇,Thin-Walled Structures 3 篇

International Journal of Solids and Structures

Numerical analyses of brittle crack growth experiments in compression using a modified phase-field theory

P. Hesammokri, P. Isaksson

doi:10.1016/j.ijsolstr.2024.112815

基于修正相场理论的压缩脆性裂纹扩展实验数值分析

There has been a huge interest in recent years in using phase-field theories for numerical analyses of fracture phenomena. However, in phase-field fracture theories, a critical aspect often involves a decomposition of the strain energy density to select physically trustworthy crack paths and to prevent interpenetration of crack surfaces. This aspect becomes even more critical in the case of mixed-mode loading under compression. To overcome these challenges, a hydrostatic-spectral-deviatoric decomposition, enhanced by separate critical energy release rates for different fracture modes, is employed in this study. In order to evaluate the enhanced decomposition strategy, a set of biaxially loaded crack experiments in global compression is designed. Samples of different geometries contain multiple flaws and holes. The experiments are numerically simulated using a unified set of material parameters and three different strain energy decomposition methods (i.e., hydrostatic-spectral-deviatoric, spectral and hydrostatic-deviatoric). Simulations using the hydrostatic-spectral-deviatoric decomposition scheme capture both intricate crack paths and critical loads in the experiments. Hence, the enhanced decomposition strategy seems capable of simulating the experiments with reasonable precision, in sharp contrast to the two commonly used decomposition strategies (spectral and hydrostatic-deviatoric).

近年来,相场理论在断裂现象数值分析中的应用引起了人们极大的兴趣。然而,在相场断裂理论中,一个关键的方面往往涉及到应变能密度的分解,以选择物理上可靠的裂纹路径,并防止裂纹表面的互渗。在压缩下的混合模式加载情况下,这一点变得更加重要。为了克服这些挑战,本研究采用了流体静力-光谱-偏差分解,并通过不同裂缝模式的不同临界能量释放率来增强。为了对增强分解策略进行评价,设计了一套全局压缩双轴加载裂纹实验。不同几何形状的样品包含多个缺陷和孔洞。采用统一的材料参数集和三种不同的应变能分解方法(静水-谱-偏、谱和静水-偏)对实验进行了数值模拟。采用静流体-频谱-偏差分解方案的模拟捕获了实验中复杂的裂纹路径和临界载荷。因此,增强的分解策略似乎能够以合理的精度模拟实验,与两种常用的分解策略(频谱和静水偏差)形成鲜明对比。


Mechanics of crack initiation, propagation and crack grain boundary interaction in bicrystal silicon using near-tip localized stress calculation

Sunil Kumar Dutta, Gaurav Singh

doi:10.1016/j.ijsolstr.2024.112811

基于近尖端局部应力计算的双晶硅裂纹萌生、扩展及裂纹晶界相互作用力学

Crack propagation and arrest are important phenomena in polycrystalline silicon. This phenomenon considerably affects the effectiveness of solar cells made up of polycrystalline silicon. To understand the crack propagation in polycrystalline silicon, it is essential to study the bicrystal first. Earlier, crack propagation has been studied in bicrystal materials primarily from the perspective of material behaviour. However, the mechanics part is largely missing. In the present work, crack propagation of bicrystal silicon during uniaxial tension has been studied at the atomistic scale. The silicon bicrystal was formed by joining two single crystals: crystal 1 and crystal 2 of different orientations. Various stages like crack initiation, propagation, arrest, re-initiation and crack grain boundary (GB) interaction have been analysed using Stress Intensity Factor (SIF), calculated from the local crack tip virial stress field. Considering the effect of crack tip velocity, the dynamic SIFs at crack propagation stage have been converted to the SIF of an equivalent static crack using the generalised expression for anisotropic material. It has been found that for the propagation stage, crack propagation continues as long as the equivalent static SIF is greater than the critical SIF (CSIF). In crystal 1, crack propagation is along the low CSIF direction. Therefore, the crack did not change its path and propagated along a straight line. On the other hand, when the crack enters to crystal 2, it follows a zigzag path. Both of these observations have been justified in terms of near-tip calculated SIFs.

裂纹扩展和止裂是多晶硅中的重要现象。这一现象极大地影响了多晶硅太阳能电池的效率。为了了解多晶硅的裂纹扩展规律,必须首先研究双晶。以前,双晶材料的裂纹扩展主要是从材料行为的角度来研究的。然而,机制部分却被忽略了。本文在原子尺度上研究了双晶硅在单轴拉伸过程中的裂纹扩展。硅双晶是由两个不同取向的单晶:晶体1和晶体2连接而成的。利用应力强度因子(SIF)分析了裂纹萌生、扩展、止裂、再萌生和裂纹晶界(GB)相互作用的各个阶段。考虑裂纹尖端速度的影响,采用各向异性材料的广义表达式将裂纹扩展阶段的动态SIF转换为等效静态裂纹的SIF。研究发现,在扩展阶段,只要等效静态SIF大于临界SIF (CSIF),裂纹就会继续扩展。在晶体1中,裂纹沿低CSIF方向扩展。因此,裂缝不改变其路径,沿直线传播。另一方面,当裂纹进入晶体2时,它遵循一个之字形路径。根据近尖端计算的sif,这两种观察结果都是合理的。


International Journal of Plasticity

Experimental Investigation and Numerical Modelling of the Cyclic Plasticity and Fatigue Behavior of Additively Manufactured 316L Stainless Steel

M. Subasic, A. Ireland, R. Mansour, P. Enblom, P. Krakhmalev, M. Åsberg, A. Fazi, J. Gårdstam, J. Shipley, P. Waernqvist, B. Forssgren, P. Efsing

doi:10.1016/j.ijplas.2024.103966

增材制造316L不锈钢循环塑性与疲劳行为的试验研究与数值模拟

This study addresses the critical need for a constitutive model to analyze the cyclic plasticity of additively manufactured 316L stainless steel. The anisotropic behavior at both room temperature and 300°C is investigated experimentally based on cyclic hysteresis loops performed in different orientations with respect to the build direction. A comprehensive constitutive model is proposed, that integrates the Armstrong-Frederick nonlinear kinematic hardening, Voce nonlinear isotropic hardening and Hill's anisotropic yield criterion within a 3D return mapping algorithm. The model was calibrated to specimens in the 0° and 90° orientations and validated with specimens in the 45° orientation. A single set of hardening parameters successfully represented the elastoplastic response for all orientations at room temperature. The algorithm effectively captured the full cyclic hysteresis loops, including historical effects observed in experimental tests. A consistent trend of reduced hardening was observed at elevated temperature, while the 45° specimen orientation consistently exhibited the highest degree of strain hardening. The applicability of the model was demonstrated by computing energy dissipation for stabilized hysteresis loops, which was combined with fatigue tests to propose an energy-based fatigue life prediction model.

本研究解决了对增材制造316L不锈钢循环塑性分析本构模型的迫切需要。实验研究了室温和300℃下不同方向的循环迟滞环的各向异性行为。提出了一种将Armstrong-Frederick非线性运动硬化、Voce非线性各向同性硬化和Hill各向异性屈服准则集成在三维返回映射算法中的综合本构模型。对0°和90°方向的试样进行了标定,并对45°方向的试样进行了验证。一组硬化参数成功地代表了室温下所有取向的弹塑性响应。该算法有效地捕获了全循环迟滞回路,包括在实验测试中观察到的历史效应。在高温下,试样的硬化程度降低,而在45°取向时,试样的应变硬化程度最高。通过对稳定滞回线能量耗散的计算,验证了该模型的适用性,并结合疲劳试验提出了基于能量的疲劳寿命预测模型。


Advancement of microstructural evolution and deformation mechanisms in AA6082 aluminum alloy under elevated-temperature tensile loading

Oleksandr Lypchanskyi, Karol Janus, Daniel Irmer, Anna Wójcik, Grzegorz Korpała, Ulrich Prahl

doi:10.1016/j.ijplas.2024.103969

高温拉伸载荷下AA6082铝合金组织演变及变形机制研究进展

This study explores the intricate interplay between strain-induced precipitation (SIP) and the underlying mechanisms that govern hot deformation in AA6082 aluminum alloy. Uniaxial tensile tests were conducted at elevated temperatures, ranging from 200°C to 400°C, and varied strain rates from 0.01 s−1 to 10 s−1. Employing advanced methodologies such as scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), energy dispersive X-ray spectrometry (EDS), and transmission electron microscopy (TEM), the research investigates the relationship between deformation, precipitation, and structural evolution. At lower strain rates, longer deformation times promote dynamic recrystallization, thereby promoting the growth of substructures with enhanced ductility. On the contrary, at higher strain rates (10 s−1), shorter deformation times inhibit such processes, resulting in a clear predominance of dislocation motion along specific slip systems and consequently influencing the mechanical response of the alloy. The results also reveal temperature-dependent deformation mechanisms, such as intragrain slip, continuous dynamic recrystallization (CDRX), and SIP phenomena, which influence the alloy's mechanical response. At 200°C, prominent work hardening dominates, while 400°C exhibits dynamic softening mechanisms. EBSD analyzes elucidate temperature-specific deformation mechanisms, including intragrain slip at 200°C and transitional phenomena at 300°C. Microstructural analysis at 200°C reveals the absence of needle- or rod-shaped precipitates. On the contrary, at 300°C, the presence of β/β' precipitates significantly influences the nucleation of β'' precipitates at the grain boundaries. At 400°C, substantial rod-shaped β' phase precipitates appear, demonstrating a complex interplay between diffusion mechanisms and strain-induced effects. In addition, the study also investigated the fracture behavior of aluminum alloy at different tensile temperatures, revealing the transition from transgranular fracture at 200°C to intergranular fracture at 300°C, as well as the shear effect of β/β' phase precipitates at this temperature. The findings provide a comprehensive understanding of the alloy behavior under diverse conditions, essential to optimize its processing parameters and mechanical properties.

本研究探讨了AA6082铝合金中应变诱导析出(SIP)之间复杂的相互作用和控制热变形的潜在机制。单轴拉伸试验在高温下进行,温度范围从200°C到400°C,应变速率从0.01 s−1到10 s−1。采用先进的方法,如扫描电子显微镜(SEM)、电子背散射衍射(EBSD)、能量色散x射线光谱(EDS)和透射电子显微镜(TEM),研究了变形、沉淀和结构演化之间的关系。在较低的应变速率下,较长的变形时间促进了动态再结晶,从而促进了子结构的生长,增强了延性。相反,在较高的应变速率下(10 s−1),较短的变形时间抑制了这一过程,导致沿特定滑移系统的位错运动明显占优势,从而影响了合金的力学响应。结果还揭示了影响合金力学响应的温度相关变形机制,如晶内滑移、连续动态再结晶(CDRX)和SIP现象。在200°C时,主要是加工硬化,而在400°C时表现为动态软化机制。EBSD分析阐明了温度特定的变形机制,包括200°C时的晶内滑移和300°C时的过渡现象。在200°C下的显微组织分析显示没有针状或棒状的沉淀。相反,在300℃时,β/β′相的存在对晶界处β′相的形核有显著影响。在400℃时,大量棒状β′相析出,表明扩散机制和应变诱导效应之间存在复杂的相互作用。此外,本研究还研究了铝合金在不同拉伸温度下的断裂行为,揭示了铝合金在200℃时的穿晶断裂向300℃时的沿晶断裂的转变,以及在该温度下β/β′相析出物的剪切作用。研究结果提供了对合金在不同条件下行为的全面了解,对优化其加工参数和力学性能至关重要。


A new failure criterion for predicting meso/micro-scale forming limit of composite metal foils

Lihuang Zheng, Jeong Whan Yoon

doi:10.1016/j.ijplas.2024.103962

一种预测复合金属箔中、微观尺度成形极限的失效准则

In order to design robust and reliable micro forming processes for composite metal foils, it is crucial to accurately forecast their forming limit under various strain paths. To date, however, there are few criteria that can effectively predict the forming limit of composite metal foils influenced by size effect. To solve this problem, a new uncoupled failure criterion is developed in this study, which considers the effects of interfacial layer, free surface roughening, grain size and strain path of heterogeneous materials, based on the deformation characteristic and failure mechanism of composite metal foils. Subsequently, it is presented the methodology for calculating the material constants of the proposed failure model. Additionally, the experimental forming limit strains of Ni/Cu clad foils with various grain sizes are utilized to show the prediction capability of the proposed model. To further confirm the application capability of the new failure criterion in practical micro forming, the finite element method incorporating the proposed criterion is employed to predict the failure behavior of Ni/Cu clad foil micro-channels in rubber pad forming. Comparisons indicate that the proposed model can accurately capture the forming limit of the composite metal foils influenced by size effect. This work provides a new scientific basis for determining the forming limit of composite metal foils.

为了设计坚固可靠的复合金属箔微成形工艺,准确预测复合金属箔在各种应变路径下的成形极限是至关重要的。然而,迄今为止,能够有效预测受尺寸效应影响的复合金属箔成形极限的准则很少。为解决这一问题,本文基于复合金属箔的变形特性和破坏机理,建立了考虑界面层、自由表面粗化、晶粒尺寸和非均质材料应变路径影响的非耦合破坏准则。然后,给出了计算所提出的破坏模型的材料常数的方法。此外,利用不同晶粒尺寸的Ni/Cu覆层箔的实验成形极限应变来验证该模型的预测能力。为了进一步验证新失效准则在实际微成形中的应用能力,采用有限元方法对镍/铜包覆箔微通道在橡胶垫成形中的失效行为进行了预测。结果表明,该模型能较准确地反映出受尺寸效应影响的复合金属箔的成形极限。为确定复合金属箔的成形极限提供了新的科学依据。


Thin-Walled Structures

Cyclic response of innovative modular joints for modular buildings under bidirectional loading

Jiajun Qin, Ping Tan, Fulin Zhou, Mengxiong Tang, Yafei Zhang, Jiajun Tan

doi:10.1016/j.tws.2024.111889

双向荷载作用下组合式建筑新型组合式节点的循环响应

Based on their dual functions of loading-bearing and energy-dissipating, modular loading-bearing and energy-dissipating joints (MVJ) was used to vertically connect modules, particularly high-rise modular building applications. Fully bolted MVJs can be assembly and disassembly rapidly, and the modules can be recycled after disassembly. Quasi-static tests were conducted on two full-scale space specimens to evaluate seismic resistance properties of the MVJs. Owing to the critical function of MVJs in the buildings, the constant axial loading on the modular column and the vertical displacement on both double beams were implemented simultaneously to simulate the worst loading condition. Owing to the characteristics of double beams under vertical forces, and the requirements of simulation of boundary conditions, a double-beam hinged loading device was proposed. The experimental results demonstrate that the proposed MVJs exhibited great moment capacity. Accordingly, the ratios of the tested average ultimate moment capacity Mu to the designed ultimate moment capacity of double beams MPbeam were 0.828 for S1 and 0.995 for S2. Diagonal cracks occurred on the ends of MVC web for both S1 and S2, indicating that the proposed MVJs were crucial in both loading-bearing and energy-dissipating; the MVC web was used to dissipate energy. Because of the insufficient weld strength between the column and the ceiling beam, as well as the bidirectional cyclic displacement observed at both ends of double beams, the error in the average ultimate moment capacity between the tested and the predicted result is 17.08%. Analysis conducted on the ductility factor and inter-storey drift ratio demonstrated the feasibility of implementing MVJs in seismic regions.

基于承重和消能的双重功能,模块化承重消能连接件(MVJ)被用于垂直连接模块,尤其是高层模块化建筑应用。全螺栓连接的 MVJ 可以快速组装和拆卸,拆卸后的模块可以回收利用。对两个全尺寸空间试样进行了准静力试验,以评估 MVJ 的抗震性能。由于 MVJ 在建筑中的重要作用,因此同时对模块柱施加恒定轴向荷载和对双梁施加垂直位移,以模拟最恶劣的荷载条件。根据双梁在垂直力作用下的特点和边界条件模拟的要求,提出了一种双梁铰接加载装置。实验结果表明,所提出的 MVJ 具有很强的弯矩承载能力。因此,S1 和 S2 的试验平均极限承载力 Mu 与双梁设计极限承载力 MPbeam 之比分别为 0.828 和 0.995。S1 和 S2 的 MVC 腹板端部都出现了对角线裂缝,这表明拟议的 MVJ 在承载和消能方面都很关键;MVC 腹板用于消能。由于支柱与顶梁之间的焊接强度不足,以及在双梁两端观察到的双向周期位移,测试结果与预测结果之间的平均极限弯矩承载力误差为 17.08%。对延性系数和层间漂移率的分析表明,在地震地区采用 MVJ 是可行的。


Study on fire temperature fields of air-supported membrane structures considering thermal-fluid-solid coupling and boundary correction

Guojun Sun, Shuo Xiao, Xiushu Qu, Suduo Xue, Jiayong Wu

doi:10.1016/j.tws.2024.111893

考虑热-流-固耦合和边界校正的气支膜结构火灾温度场研究

The study analyzed and compared the effects of thermal-fluid-solid coupling dynamic boundary conditions and traditional fixed-boundary conditions on the distribution of the temperature field under fires. The feasibility of simulating the temperature field distribution was confirmed by using thermal-fluid-solid coupling dynamic boundary conditions. Then, the traditional temperature field analysis methods were corrected by including a flow-based heat exchange coefficient, and the feasibility of this approach was also confirmed. The fire temperature field in a rectangular air-supported membrane structure was analyzed through parameterization. The fire temperature field model of the air-supported membrane structure was established using temperature field data fitting. Furthermore, the study explored the high-temperature material properties of P-type membranes and analyzed and compared the temperature field of the air-supported membrane structure with time-varying mechanical properties of the membrane material to that without time-varying properties.

分析比较了热-流-固耦合动态边界条件和传统固定边界条件对火灾下温度场分布的影响。验证了采用热-流-固耦合动态边界条件模拟温度场分布的可行性。通过引入基于流动的换热系数,对传统的温度场分析方法进行了修正,并验证了该方法的可行性。通过参数化分析了矩形气支膜结构的火灾温度场。通过温度场数据拟合,建立了气支膜结构的火灾温度场模型。进一步研究了p型膜的高温材料性能,分析比较了具有时变膜材料力学性能的气支膜结构与无时变膜材料力学性能的气支膜结构的温度场。


Prediction of vibration fatigue life of fiber reinforced composite thin plates with functionally graded coating under base random excitation

Cong Sun, Yao Yang, Hui Li, Hesong Xu, Feng Zhao, Zhuo Xu, Guowei Sun, Junxue Hou, He Li

doi:10.1016/j.tws.2024.111891

基随机激励下功能梯度涂层纤维增强复合材料薄板振动疲劳寿命预测

This study presents the prediction of the vibration fatigue life of fiber reinforced composite thin plates (FRCTPs) with the functionally graded coating (FGC) under base random excitation. A dynamic model of an FGC-FRCTP under such an excitation loading is developed using the first-order shear deformation theory, random vibration theory, complex modulus method, etc. The natural frequency, stress frequency response function, and stress power spectral density curves are solved by the Rayleigh-Ritz method and frequency domain random vibration analysis approach. Moreover, the random fatigue life of the FGC-FRCTPs is successfully predicted by the Dirlik, Bendat, and Tovo-Benasciutti distribution. Finally, the preparation approaches of the FGC and the coated specimens are introduced, and detailed experimental investigations are performed. It has been found that the prediction errors of fatigue life using the Bendat, Dirlik and Tovo-Benasciutti distributions are less than -14.6 %, which proves that the current model can be employed to evaluate the fatigue resistance of the FGC-FRCTPs. Also, the impact of key coating parameters on the vibration fatigue life of the studied coated structures is evaluated. To improve their fatigue resistance, it is advised to select a large coating area, coating thickness ratio, and functionally graded index with the coating position near the constrained edge of the FGC-FRCTPs.

研究了基随机激励下功能梯度涂层纤维增强复合材料薄板的振动疲劳寿命预测。利用一阶剪切变形理论、随机振动理论、复模量法等建立了FGC-FRCTP在这种激励荷载作用下的动力模型。采用瑞利-里兹法和频域随机振动分析法求解了结构的固有频率、应力频响函数和应力功率谱密度曲线。此外,通过Dirlik、Bendat和Tovo-Benasciutti分布成功预测了fgc - frctp的随机疲劳寿命。最后介绍了FGC和涂层试样的制备方法,并进行了详细的实验研究。结果表明,利用Bendat、Dirlik和Tovo-Benasciutti分布对fgc - frctp疲劳寿命的预测误差小于- 14.6%,证明该模型可用于fgc - frctp的疲劳抗力评估。分析了涂层关键参数对涂层结构振动疲劳寿命的影响。为提高fgc - frctp的抗疲劳性能,建议选择较大的涂层面积、涂层厚度比和功能分级指标,且涂层位置靠近约束边缘。



来源:复合材料力学仿真Composites FEM
ACTMechanicalAdditiveSystemDeform振动疲劳断裂复合材料非线性建筑电子增材焊接裂纹理论化机材料控制螺栓
著作权归作者所有,欢迎分享,未经许可,不得转载
首次发布时间:2024-11-14
最近编辑:19天前
Tansu
签名征集中
获赞 6粉丝 0文章 776课程 0
点赞
收藏
作者推荐

【新文速递】2024年4月15日复合材料SCI期刊最新文章

今日更新:Composite Structures 4 篇,Composites Part A: Applied Science and Manufacturing 1 篇,Composites Part B: Engineering 1 篇,Composites Science and Technology 1 篇Composite StructuresMulti-scale concurrent topology optimization of cellular structures with multiple microstructures for minimizing dynamic response in the time domainJian Wang, Yan Zhang, Xiaoyu Wang, Xuyang Zheng, Zhiyong Ma, Wei-Hsin Liao, Nan Zhu, Qiang Gaodoi:10.1016/j.compstruct.2024.118124多微结构元胞结构的多尺度并行拓扑优化,以实现时域动态响应最小化This paper proposes a concurrent topology optimization method for optimizing the structures that are periodically filled with multiple microstructures excited by dynamic response in the time domain. At the macroscale, different microstructures are considered as different materials. To generate the various distribution of different microstructures, a multi-material interpolation approach based on the Solid Isotropic Material with Penalization (SIMP) is integrated. At the microscale, the energy-based homogenization method (EBHM) is employed to determine the macroscopic effective properties of the microstructures. All macroscale elements with identical material are represented by a distinct microstructure. For the proportional damping model, the HHT-α is implemented as a time integration technique to obtain the dynamic response of multi-scale and assumed multi-material structures. The objective function of the topology optimization problem is to minimize the mean dynamic compliance. Combined differentiate-then-discretize method with the adjoint variable method, the sensitivity analysis applies the gradient-based Zhang-Paulino-Ramos Jr. (ZPR) algorithm or Method of Moving Asymptotes (MMA) to update the design variables under multiple constraints in the time and space-discretized system. The proposed approach is numerically performed through 2D and 3D examples to demonstrate its effectiveness.本文提出了一种并行拓扑优化方法,用于在时域动态响应激励下周期性填充多个微结构的结构优化。在宏观尺度上,不同的微观结构被认为是不同的材料。为了生成不同微观结构的不同分布,提出了一种基于固体各向同性材料惩罚(SIMP)的多材料插值方法。在微观尺度上,采用基于能量的均匀化方法(EBHM)来确定微观结构的宏观有效性质。所有具有相同材料的宏观元素都具有不同的微观结构。对于比例阻尼模型,HHT-α作为时间积分技术实现了多尺度和假设多材料结构的动态响应。拓扑优化问题的目标函数是使平均动态柔度最小。灵敏度分析将微分-离散化方法与伴随变量法相结合,采用基于梯度的Zhang-Paulino-Ramos Jr. (ZPR)算法或移动渐近线法(MMA)对时空离散化系统中多约束条件下的设计变量进行更新。通过二维和三维算例验证了该方法的有效性。A generic design motif for metamaterials with controllable nonlinearity & guided deformationXiaofeng Geng, Zhipeng Zhao, Yingqing Guo, Jiqiang Wang, Hu Ding, Xingjian Jingdoi:10.1016/j.compstruct.2024.118125具有可控非线性和导向变形的超材料的通用设计母题Structure design motifs take an essential role in creating materials or metamaterials with superior mechanics or special functions. However, a fundamental question naturally arising and remaining unknown is related to how to effectively design an engineered material structure with “adjustable and predictable” nonlinear mechanic properties conveniently. Here we propose a very simple but versatile design motif, named as bq-structure, which can provide superior flexibility in achieving various nonlinear properties, including 200 % larger and designable ranges of quasi-zero stiffness, negative stiffness, and multi-stable stiffness, etc, that original material or traditional beam-based design motifs cannot provide. The proposed design motif has sufficient reliability in nonlinear manipulation with a “guided & controllable” manner instead of “trail-and-error attempts” existing in most existing ones. A prototyped vibration isolation unit can achieve a resonant frequency less than 1 Hz easily which cannot be done with many other methods of similar size and payload. Given the large elastic deforming capacity and ductility in structural scale, the superb nonlinearity regime is generally designable with various structure parameters, uniquely providing a superior optimization tool with this novel design motif considering various real application requirements for advanced materials design, energy storage or conversion, mechanical vibration mitigation, and robotic systems etc结构设计图案在创造具有优越力学或特殊功能的材料或超材料方面起着至关重要的作用。然而,如何有效地、方便地设计具有“可调可预测”非线性力学性能的工程材料结构,是一个自然产生而又未知的基本问题。在这里,我们提出了一个非常简单但通用的设计母题,称为bq结构,它可以提供优越的灵活性,以实现各种非线性特性,包括200 %的可设计范围的准零刚度,负刚度和多稳定刚度等,这是原始材料或传统的基于梁的设计母题所不能提供的。本文提出的设计母题在非线性操作中具有足够的可靠性,具有“引导可控”的方式,而不是大多数现有设计母题存在的“跟踪-错误尝试”。原型隔振单元可以轻松实现小于1 Hz的谐振频率,这是许多其他类似尺寸和有效载荷的方法无法实现的。由于具有较大的弹性变形能力和结构尺度上的延展性,其优异的非线性体系通常可设计为各种结构参数,独特地为先进材料设计、能量存储或转换、机械振动缓解和机器人系统等各种实际应用需求提供了优越的优化工具Fatigue and post-fatigue behavior of FRCM-concrete specimens under direct shear and bending conditionsAngelo Savio Calabrese, Pierluigi Colombi, Tommaso D'Antinodoi:10.1016/j.compstruct.2024.118129直接剪切和弯曲条件下frcm -混凝土试件的疲劳及后疲劳行为The combined effect of cyclic loading and steel rebar corrosion can determine the premature deterioration of reinforced concrete (RC) structures subjected to dynamic and environmental actions. The use of fabric-reinforced cementitious matrix composites (FRCM) is a promising solution to extend the fatigue life of RC structures. Externally bonded FRCMs are applied to the tension side of structural members to reduce the rebar stress level, thus delaying fatigue crack nucleation and/or propagation. A key aspect for the design of FRCM strengthening of these structures is the matrix-fiber bond behavior under fatigue loading. In this paper, a critical review of currently available studies on the fatigue behavior of FRCM-strengthened RC beams is presented. Then, the results of 25 bond tests on PBO FRCM-concrete specimens are provided and discussed. These tests include both single-lap direct shear and modified beam tests performed in quasi-static and cyclic mode. The results obtained show that the cyclic load may induce progressive debonding at the matrix-fiber interface with rupture of fiber filaments. Modified beam tests are more affected by these phenomena than direct shear tests. The rupture of fiber filaments is confirmed by the results of post-fatigue tests that show capacities lower than those of corresponding quasi-static tests.循环荷载和钢筋腐蚀的共同作用可以决定钢筋混凝土结构在动力和环境作用下的过早劣化。纤维增强胶凝基复合材料(FRCM)是延长钢筋混凝土结构疲劳寿命的一种很有前途的方法。外粘结frp材料应用于构件受拉侧,以降低钢筋应力水平,从而延缓疲劳裂纹的形核和/或扩展。疲劳载荷下的基体-纤维粘结性能是frp加固设计的一个关键方面。本文对目前已有的frp增强RC梁疲劳性能研究进行了综述。给出了PBO frp -混凝土试件25次粘结试验结果并进行了讨论。这些试验包括在准静态和循环模式下进行的单搭接直剪和修改梁试验。结果表明:循环荷载可引起纤维-基体界面的渐进式剥离,纤维细丝断裂。修正梁试验比直接剪切试验受这些现象的影响更大。疲劳后试验结果证实了纤维长丝的断裂,其承载力低于相应的准静态试验结果。Experimental and numerical analysis of low-velocity impact and compression after impact responses of novel 3D hybrid compositesKe Wang, Farid Taheridoi:10.1016/j.compstruct.2024.118133新型三维混杂复合材料低速冲击和冲击后压缩响应的实验与数值分析Rising environmental concerns and the push to cut carbon emissions have resulted in increased incorporation of lightweight materials to improve fuel efficiency across industries. Fiber Metal Laminates (FMLs), known for superior properties, are widely used in aerospace. In the same vein, the recently developed 3D Fiber-Metal Laminates (3DFMLs) with a 3D composite core have been demonstrated to offer remarkable performance despite fabrication challenges.Two innovative 3D hybrid composites (3DFML-PI and 3DHC-PI) are introduced. These FMLs integrate plastic inserts to overcome the fabrication hurdles experienced by the original 3DFMLs and enhance their mechanical properties. Notably, 3DFML-PI shows comparatively an exceptional impact resistance with a higher perforation threshold, highlighting the efficacy of plastic inserts. Additionally, 3DFML-PI exhibits higher compressive strength, suggesting improved consolidation of the 3D composites. Comparison of the compression-after-impact (CAI) performances also underscores the advantages of high flexural stiffness and localized damage. The research justifies further exploration and implementation of these innovative materials in practical applications requiring lightweight materials with high specific strength, stiffness, impact resistance, and economic sustainability.日益严重的环境问题和减少碳排放的努力,导致各行各业越来越多地采用轻质材料,以提高燃油效率。金属纤维层压板(FMLs)以其优越的性能被广泛应用于航空航天领域。同样,最近开发的3D纤维-金属层压板(3DFMLs)具有3D复合材料核心,尽管在制造方面存在挑战,但已被证明具有卓越的性能。介绍了两种新型的三维复合材料3DFML-PI和3DHC-PI。这些FMLs集成了塑料插入件,克服了原始3DFMLs的制造障碍,提高了其机械性能。值得注意的是,3DFML-PI具有相对优异的抗冲击性,具有较高的穿孔阈值,突出了塑料镶件的有效性。此外,3DFML-PI具有更高的抗压强度,表明3D复合材料的固结得到改善。冲击后压缩(CAI)性能的比较也强调了高抗弯刚度和局部损伤的优势。这项研究证明了这些创新材料在实际应用中的进一步探索和实施,这些材料需要具有高比强度、刚度、抗冲击性和经济可持续性的轻质材料。Composites Part A: Applied Science and ManufacturingUncut fiber analysis using fiber deflection and cutting forces in carbon fiber-reinforced plastics during rotation of the cutting toolDong-Gyu Kim, Seung-Han Yangdoi:10.1016/j.compositesa.2024.108206利用切削刀具旋转过程中碳纤维增强塑料的纤维挠度和切削力对未切削纤维进行分析Cutting, milling, and drilling during the manufacture of carbon fiber-reinforced plastics (CFRPs) is an active field of research. It is challenging to analyze cutting characteristics during cutting tool rotation because the chip thickness, fiber cutting angle, and specific cutting force change. Here, we used a mechanical model to study the cutting forces and fiber deflections that develop as the cutting tool rotates during CFRP milling. The fiber and matrix were modeled as a beam, and the cutting force and fiber deflection were analyzed according to the fiber cutting angle. We explored how uncut fiber status and surface roughness were affected. If the fiber deflection caused by transverse cutting forces was not eliminated before the cutting tool rotation angle attained 180°, some fibers were not cut. Serious defects developed when uncut fibers were not generated at certain fiber orientation angles.碳纤维增强塑料(CFRPs)制造过程中的切削、铣削和钻孔是一个活跃的研究领域。由于切屑厚度、纤维切削角度和切削比力的变化,刀具旋转过程中的切削特性分析具有一定的挑战性。在这里,我们使用力学模型来研究CFRP铣削过程中刀具旋转时产生的切削力和纤维挠度。将纤维和基体建模为一根梁,根据纤维切割角度分析了切割力和纤维挠度。我们探索了未切割的纤维状态和表面粗糙度是如何受到影响的。如果在刀具旋转角度达到180°之前没有消除横向切削力引起的纤维挠曲,则部分纤维未被切割。在一定的纤维取向角度下,未切割的纤维产生时,会产生严重的缺陷。Composites Part B: EngineeringBamboo as a natural optimized fiber reinforced composite: interfacial mechanical properties and failure mechanismsXiaohan Chen, Xianke Wang, Xun Luo, Lin Chen, Yuquan Li, Jiarui Xu, Zengqian Liu, Chunping Dai, Hu Miao, Huanrong Liudoi:10.1016/j.compositesb.2024.111458竹作为一种天然优化纤维增强复合材料:界面力学性能及破坏机制Bamboo is a typical natural fiber-reinforced composite with an optimized distribution of vascular bundles as reinforcement and parenchyma tissues as bio-matrix. The interfacial bonding performance between vascular bundles and parenchyma tissue is critical for the mechanical properties and failure mechanisms of bamboo. This study employed pull-out tests to determine the interfacial shear strength (IFSS) between bamboo vascular bundles and parenchyma tissue and evaluate the critical embedded lengths () of vascular bundles. The effects of embedded vascular bundle lengths on interfacial strength and failure behaviors were also investigated. The results revealed a value of 2.51 mm, lower than the majority of plant fiber-reinforced composite materials, with an IFSS of around 20 MPa, surpassing most artificial bamboo fiber composites. The pull-out process of the vascular bundles involved elasticity, debonding, and sliding friction stage, where debonding energy absorption (DEA) outweighed frictional energy absorption (FEA) and increasing with embedded length. The primary failure features include interfacial debonding, parenchyma tissue ripping, delamination of fiber thin layers, and fiber breakage. Moreover, the parenchyma cells between the two fiber sheaths and at the top of the bamboo block readily detached. The interfacial failure mechanisms of bamboo included debonding, reinforcement, and matrix failure, with the proportions varying as the embedded length increased. Quantitative analysis of the interfaces structure and mechanical properties between vascular bundles and parenchyma tissues could provide a reference for the biomimicry of bamboo structures and the manufacturing of natural fiber-reinforced composite materials.竹是一种典型的天然纤维增强复合材料,以维管束为增强材料,以薄壁组织为生物基质。维管束与薄壁组织之间的界面结合性能对竹材的力学性能和破坏机制至关重要。本研究采用拔除试验测定了竹材维管束与薄壁组织的界面剪切强度(IFSS),并评估了维管束的临界嵌入长度()。研究了嵌入维管束长度对界面强度和破坏行为的影响。结果表明,IFSS值为2.51 mm,低于大多数植物纤维增强复合材料,IFSS约为20 MPa,超过大多数人造竹纤维复合材料。维管束的拔出过程分为弹性阶段、脱粘阶段和滑动摩擦阶段,其中脱粘能量吸收(DEA)大于摩擦能量吸收(FEA),且随着埋置长度的增加而增加。主要的破坏特征包括界面脱粘、薄壁组织撕裂、纤维薄层脱层和纤维断裂。此外,两种纤维鞘之间和竹块顶部的薄壁细胞容易脱落。竹材界面破坏机制主要有脱粘破坏、加固破坏和基体破坏,其破坏比例随埋置长度的增加而变化。定量分析竹材维管束与薄壁组织之间的界面结构和力学性能,可为竹材结构的仿生学和天然纤维增强复合材料的制造提供参考。Composites Science and TechnologyA novel strategy to prepare rubber/clay nanocomposites via compounding clay gel into cocoamidopropyl betaine modified styrene butadiene rubberZilong Chen, Jian Li, Zhanxu Li, Jun Lin, Liqun Zhang, Shaojian Hedoi:10.1016/j.compscitech.2024.110602 将粘土凝胶复配至椰酰胺丙基甜菜碱改性丁苯橡胶中制备橡胶/粘土纳米复合材料的新策略In this study, high performance styrene-butadiene rubber (SBR)/clay nanocomposites (NCs) modified by cocoamidopropyl betaine (CAPB) are prepared via an efficient and facile strategy. CAPB-modified SBR was compounded with clay gel via gel compounding method to obtain SBR/clay composites. The effect of processing condition and CAPB on the mechanical properties of the SBR/clay composites was investigated. XRD and TEM results show that clay dispersion in SBR matrix is significantly improved due to the success of CAPB in the hydrophilic modification of SBR. The clay-SBR interaction is enhanced and more SBR molecular chains are adsorbed to the clay, significantly improving the mechanical properties of SBR/CAPB/clay NCs, as demonstrated by SEM and DMA. The maximum tensile strength of SBR/CAPB/clay NCs achieved 16.3 MPa at a clay loading of 40 phr, which is 10 times that of pure SBR. The tensile strength of the SBR/CAPB/clay NC incorporated with 20 phr clay has exceeded that of the SBR composite incorporated with 40 phr commercial organic clay. This work demonstrates that this strategy, which combines the CAPB-modification of SBR with the gel compounding method, is an effective and feasible method to improve the mechanical strength of SBR.本研究采用高效、简便的方法制备了椰酰胺丙基甜菜碱(CAPB)改性的高性能丁苯橡胶(SBR)/粘土纳米复合材料(NCs)。采用凝胶复配法将改性SBR与粘土凝胶复配,得到SBR/粘土复合材料。研究了工艺条件和CAPB对SBR/粘土复合材料力学性能的影响。XRD和TEM结果表明,CAPB成功地对SBR进行了亲水性改性,显著改善了SBR基体中粘土的分散性。SEM和DMA分析表明,黏土与SBR的相互作用增强,更多的SBR分子链被吸附到黏土上,显著改善了SBR/CAPB/clay NCs的力学性能。SBR/CAPB/clay NCs在40 phr黏土加载下的最大抗拉强度达到16.3 MPa,是纯SBR的10倍。掺加20phr粘土的SBR/CAPB/clay NC的抗拉强度超过掺加40phr商用有机粘土的SBR复合材料。研究表明,将capb改性SBR与凝胶复合相结合的策略是提高SBR机械强度的有效可行的方法。来源:复合材料力学仿真Composites FEM

未登录
还没有评论
课程
培训
服务
行家
VIP会员 学习 福利任务 兑换礼品
下载APP
联系我们
帮助与反馈