RationalDMIS 7.1 一点法 （快速建立零件坐标系）
建立原理：确定坐标系的三个轴向方向和坐标原点（右手坐标系）
特征的选择：根据图纸和工艺要求，尽量选取工件的基准特征建系
测量建系特征时的要求：在基准特征尽量大的范围内测量该特征
常用的方法：生成坐标系（3-2-1法），三点拟合，多点拟合，最佳拟合，迭代对齐
坐标系的检查：坐标系建立完成后，要检查方向是否正确，坐标值偏差是否合适。
RationalDMIS 7.1 一点法 （快速建立零件坐标系）
这个功能利用一个单一的测点或当前测头位置创建参考系.
山涧果子提示：
对于测量需要注意的地方：
在测量点的情况下（测量的类型为POINT），如果测量点数设置为1，那么将按照定义的理论值去测量。如果设置为0,将记录当时测针红宝石球心的坐标，将此作为当前测量点实际值。
通 过 RationalDMIS 7.1 测量软件 坐 标 系 的 平 移 功 能 ， 将 CMM 机 器 坐 标 原 点 平 移 到手动模式（MODE/MAN）下测量的第一点而创建的测量坐标系称之为 一点法。
RE:一点建坐标系，首先借助的是机器坐标器，但是更换零件后，需要同样的摆放位置（最好是工件某部分平行与机器的X或Y轴）。
提示：
这个功能利用一个单一的测点创建参考系，建立坐标时尽量使自己建立的坐标系与机器坐标系在方向上一致。参考系的轴会平行于选择的参考系. 此功能一般用于程序自动建立参考系之前快速建立预参考系。
一点法零件装夹原则：
（1）尽可能将零件的主基准与坐标机的平台平行或紧贴装夹；
（2）尽可能使零件的更多的面与三坐标轴平行或垂直；
创建 一点法坐标系遵循的基本原则：
① 用于创建 一点法 坐标系而手动操作测量的一点，在工件上的位置需有较强的可分辨性和可测性；
② 创建 一点法坐标系编程方式不仅适用于单件精密工件重复性测量，更适用于批量件、多批次、不同时空循环测量；
③ 适用于有固定装夹方式工件的测量。
④ “可简化为点”的元素均可以用于创建 PT 坐标系(如点，圆，圆弧，球 等)；
坐标功能应用
利用坐标系平移功能对机器坐标系原点进行平移。
测量流程如下：
① 手动模式（MODE/MANUAL），手动操作测量有明显位置特征的一点(Point)（或将探针放置到圆 CENTERCIR 中心:）；
② 创建 一点法坐标系(粗建坐标系）；
③程序模式（MODE/PROG,MAN）自动测量用于创建 3-2-1 坐标系的特征元素 ；
④ 创建工件坐标系（精建坐标系）
⑤ 自动测量需要评价的元素
⑥构造，公差评价，输出报告。
RationalDMIS 7.1 一点法 （快速建立零件坐标系）具体操作步骤：
1.探针放置到圆 CENTERCIR 中心，点击后即取探针的球心坐标生成一个点（当前测头位置创建一个点）
2.平移坐标系（一点法）
3.程序模式，自动测量圆，半精建坐标系。
4.给定安全平面，自动测量平面，直线，点，精建坐标系。
该方法一般适用于工件形状规则的机加工件的坐标系的建立，，有精度较高的基准特征可以测量。先测量和构造建立坐标系所需的特征，然后生成坐标构建零件坐标系。（找正，旋转，平移）
5.模型对齐
6.测量被测元素（需要评价的几何元素）
7.公差评价
8.输出报告
相关文章，在仿真秀官网搜索：
RationalDMIS7.0工件测量之特征阵列+镜像使用方法（模具+电极/铜公）
RationalDMIS四面分中（模具/铜公/电极）
RationalDMIS 铜公测量之菜单式 HLL
RationalDMIS 7.1 建立零件坐标系3-2-1法则
RationalDMIS7.1坐标系 （汇总）
RationalDMIS 7.0 回转体坐标系建立实例
RationalDMIS 7.0 一点建坐标系
RationalDMIS一点法构建坐标系
$$/* Header
DMISMN/'Created by [爱科腾瑞科技(北京)有限公司-041520-DEMO] on 星期四, 三月 26, 2020', 4.0
UNITS/MM, ANGDEC, MMPS
WKPLAN/XYPLAN
PRCOMP/ON
TECOMP/ON
FLY/1.0000
MODE/MAN
SNSET/APPRCH, 2.0000
SNSET/RETRCT, 2.0000
SNSET/DEPTH, 0.0000
SNSET/SEARCH, 10.0000
SNSET/CLRSRF, 30.0000
RECALL/D(MCS)
SNSLCT/S(L20-D4)
GEOALG/BF, LSTSQR
GEOALG/ANGLB, DEFALT
GEOALG/CIRCLE, LSTSQR
GEOALG/ARC, LSTSQR
GEOALG/PLANE, LSTSQR
$$
$$
$$*/
MODE/MAN
F(PT1)=FEAT/POINT,CART,24.0000,27.2872,33.0044,0.0000,0.0000,1.0000
MEAS/POINT, F(PT1), 0
PTMEAS/CART, 24.0000,27.2872,33.0044,0.0000,0.0000,1.0000
ENDMES
D(CRD1) = TRANS/XORIG, FA(PT1), YORIG, FA(PT1), ZORIG, FA(PT1)
MODE/PROG,MAN
F(CIR1)=FEAT/CIRCLE,INNER,CART,-0.0000,0.0000,-3.0011,-0.0000,0.0000,1.0000, 10.0000
$$ Measurement points are created through nominal points
MEAS/CIRCLE, F(CIR1), 4
GOTO/CART, 0.0000, 0.0000, 28.9956
GOTO/CART, -1.0033, 0.0000, 28.9956
GOTO/CART, -1.0033, 0.0000, 26.9989
PTMEAS/CART, -5.0000, 0.0000, -3.0011, 1.0000, 0.0000, 0.0000
PTMEAS/CART, 0.0000, 5.0000, -3.0011, 0.0000, -1.0000, 0.0000
PTMEAS/CART, 5.0000, 0.0000, -3.0011, -1.0000, -0.0000, -0.0000
PTMEAS/CART, 0.0000, -5.0000, -3.0011, 0.0000, 1.0000, 0.0000
GOTO/CART, 0.0000, -1.0033, 26.9989
ENDMES
D(CRD2) = TRANS/XORIG, FA(CIR1), YORIG, FA(CIR1)
$$ MACRO: EASI_CLEARPLN_GOTO
$$ FUNCTION: CLEARANCE SURFACE IMPLEMENTATION
$$ Move machine CLEAR SURFACE DIST above the current clear surface
$$ plane and then move machine parallel to the clear surface plane
$$ ALL Macro parameters are in PCS and Current UNITS
$$ Last update: 3-1-04 Add mode checking. only works in PROG MODE
$$ Last update: 8-24-04 Clear position is based on the surface of
$$
$$ This sample DMIS Macro is provided by External-Array Software, Inc.
$$ It should be modified for your own use. There is no guarantee for
$$ the quality of this Macro. November, 2003
M(EASI_CLEARPLN_GOTO) = MACRO/ISNOM, TARX, TARY, TARZ
DECL/LOCAL, REAL, CCX, CCY, CCZ, CCI, CCJ, CCK
DECL/LOCAL, REAL, CURX, CURY, CURZ, TD, CLRDIST, SDIAM
DECL/LOCAL, CHAR, 255, CLRLABEL, FLABEL, MMODE, SNAME
MMODE = VALUE/MODE
CLRLABEL = VALUE/SNSET, CLRSRF
IF/ ( (LEN(CLRLABEL) .GT. 0) .AND. (MMODE .EQ. 'PROG,MAN') )
CLRDIST = VALUE/SNSET, CLRSRF, DIST
FLABEL = ASSIGN/'FA'
IF/ ISNOM .EQ. 0
FLABEL = ASSIGN/'F'
ENDIF
CCX = OBTAIN/FLABEL(@CLRLABEL), 3
CCY = OBTAIN/FLABEL(@CLRLABEL), 4
CCZ = OBTAIN/FLABEL(@CLRLABEL), 5
CCI = OBTAIN/FLABEL(@CLRLABEL), 6
CCJ = OBTAIN/FLABEL(@CLRLABEL), 7
CCK = OBTAIN/FLABEL(@CLRLABEL), 8
SNAME = VALUE/SNSLCT
SDIAM = OBTAIN/SS(SNAME), 8
CCX = ASSIGN/CCX + CCI * SDIAM/2
CCY = ASSIGN/CCY + CCJ * SDIAM/2
CCZ = ASSIGN/CCZ + CCK * SDIAM/2
CURX = VALUE/GOTOM, XAXIS
CURY = VALUE/GOTOM, YAXIS
CURZ = VALUE/GOTOM, ZAXIS
TD = ASSIGN/(CURX - CCX) * CCI + (CURY - CCY) * CCJ + (CURZ - CCZ) * CCK
IF/ TD .LT. CLRDIST
TD = ASSIGN/(CLRDIST - TD)
GOTO/CURX+CCI*TD, CURY+CCJ*TD, CURZ+CCK*TD
ENDIF
TD = ASSIGN/(TARX - CCX) * CCI + (TARY - CCY) * CCJ + (TARZ - CCZ) * CCK
IF/ TD .LT. CLRDIST
TD = ASSIGN/(CLRDIST - TD)
GOTO/TARX+CCI*TD, TARY+CCJ*TD, TARZ+CCK*TD
ENDIF
ENDIF
ENDMAC
SNSET/APPRCH, 3
SNSET/RETRCT, 3
SNSET/DEPTH, 0.0000
SNSET/SEARCH, 10.0000
SNSET/CLRSRF, F(EA_XYPLANE), 30.0000
F(PLN1)=FEAT/PLANE,CART,25.0935,25.6989,-0.0011,0.0000,0.0000,1.0000
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 0, 0.0000, -1.0033, 31.9967
MEAS/PLANE, F(PLN1), 4
GOTO/CART, 0.0000, -1.0033, 31.9967
GOTO/CART, -17.9751, 4.2482, 31.9967
PTMEAS/CART, -17.9751, 4.2482, -0.0011, 0.0000, 0.0000, 1.0000
PTMEAS/CART, -16.4134, 57.6666, -0.0011, 0.0000, 0.0000, 1.0000
PTMEAS/CART, 73.8886, 60.4458, -0.0011, 0.0000, 0.0000, 1.0000
PTMEAS/CART, 60.8737, -19.5651, -0.0011, 0.0000, 0.0000, 1.0000
ENDMES
D(CRD3) = DATSET/FA(PLN1), ZDIR
D(CRD3) = TRANS/ZORIG, FA(PLN1)
SNSET/APPRCH, 3
SNSET/RETRCT, 3
SNSET/DEPTH, 0.0000
SNSET/SEARCH, 10.0000
SNSET/CLRSRF, FA(PLN1), 30.0000
F(LN1)=FEAT/LINE,BND,CART,-18.4198,-27.2872,-17.5472,38.1666,-27.2872,-17.9901,0.0000,-1.0000,0.0000
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 60.8737, -19.5651, 31.9967
MEAS/LINE, F(LN1), 2
GOTO/CART, 60.8737, -19.5651, 31.9967
GOTO/CART, -18.4198, -32.2839, 31.9967
PTMEAS/CART, -18.4198, -27.2872, -17.5472, -0.0000, -1.0000, -0.0000
PTMEAS/CART, 38.1666, -27.2872, -17.9901, -0.0000, -1.0000, -0.0000
ENDMES
F(PT2)=FEAT/POINT,CART,-24.0000,-10.4509,-3.1569,-1.0000,0.0000,0.0000
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, -28.9967, -10.4509, -3.1569
MEAS/POINT, F(PT2), 1
GOTO/CART, 38.1666,-32.2839,31.9967
GOTO/CART, -28.9967,-10.4509,31.9967
PTMEAS/CART, -24.0000,-10.4509,-3.1569,-1.0000,0.0000,0.0000
ENDMES
D(CRD4) = DATSET/FA(PLN1), ZDIR, ZORIG, FA(LN1), XDIR, YORIG, FA(PT2), XORIG
D(CRD4) = TRANS/ZORIG, -35, YORIG, -0, XORIG, -0
$$ Set.CAD2PCS.CADM_1
MODE/PROG,MAN
SNSET/APPRCH, 2
SNSET/RETRCT, 2
SNSET/DEPTH, 0.0000
SNSET/SEARCH, 10.0000
SNSET/CLRSRF, FA(PLN1), 30.0000
F(点-1)=FEAT/POINT,CART,5.4582,79.4481,35.0000,0.0000,0.0000,1.0000
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 5.4582, 79.4481, 38.9967
MEAS/POINT, F(点-1), 1
GOTO/CART, 5.4582,79.4481,66.9967
PTMEAS/CART, 5.4582,79.4481,35.0000,0.0000,0.0000,1.0000
ENDMES
F(点-2)=FEAT/POINT,CART,6.7215,25.7627,35.0000,0.0000,0.0000,1.0000
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 6.7215, 25.7627, 38.9967
MEAS/POINT, F(点-2), 1
GOTO/CART, 6.7215,25.7627,66.9967
PTMEAS/CART, 6.7215,25.7627,35.0000,0.0000,0.0000,1.0000
ENDMES
F(点-3)=FEAT/POINT,CART,77.9560,13.5173,35.0000,0.0000,0.0000,1.0000
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 77.9560, 13.5173, 38.9967
MEAS/POINT, F(点-3), 1
GOTO/CART, 77.9560,13.5173,66.9967
PTMEAS/CART, 77.9560,13.5173,35.0000,0.0000,0.0000,1.0000
ENDMES
F(点-4)=FEAT/POINT,CART,118.0692,47.8942,35.0000,0.0000,0.0000,1.0000
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 118.0692, 47.8942, 38.9967
MEAS/POINT, F(点-4), 1
GOTO/CART, 118.0692,47.8942,66.9967
PTMEAS/CART, 118.0692,47.8942,35.0000,0.0000,0.0000,1.0000
ENDMES
F(点-5)=FEAT/POINT,CART,99.6067,89.6792,35.0000,0.0000,0.0000,1.0000
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 99.6067, 89.6792, 38.9967
MEAS/POINT, F(点-5), 1
GOTO/CART, 99.6067,89.6792,66.9967
PTMEAS/CART, 99.6067,89.6792,35.0000,0.0000,0.0000,1.0000
ENDMES
F(点-6)=FEAT/POINT,CART,38.9784,84.3764,35.0000,0.0000,0.0000,1.0000
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 38.9784, 84.3764, 38.9967
MEAS/POINT, F(点-6), 1
GOTO/CART, 38.9784,84.3764,66.9967
PTMEAS/CART, 38.9784,84.3764,35.0000,0.0000,0.0000,1.0000
ENDMES
F(点-7)=FEAT/POINT,CART,11.1410,113.7743,32.2543,0.0000,0.1190,0.9929
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 11.1410, 114.2498, 36.2226
MEAS/POINT, F(点-7), 1
GOTO/CART, 11.1410,114.2498,66.9967
PTMEAS/CART, 11.1410,113.7743,32.2543,0.0000,0.1190,0.9929
ENDMES
F(点-8)=FEAT/POINT,CART,29.2152,100.4142,34.0735,0.0000,0.1606,0.9870
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 29.2152, 101.0561, 38.0183
MEAS/POINT, F(点-8), 1
GOTO/CART, 29.2152,101.0561,66.9967
PTMEAS/CART, 29.2152,100.4142,34.0735,0.0000,0.1606,0.9870
ENDMES
F(点-9)=FEAT/POINT,CART,80.2930,99.0131,29.1150,0.0000,0.5496,0.8354
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 80.2930, 101.2096, 32.4540
MEAS/POINT, F(点-9), 1
GOTO/CART, 80.2930,101.2096,66.9967
PTMEAS/CART, 80.2930,99.0131,29.1150,0.0000,0.5496,0.8354
ENDMES
F(点-10)=FEAT/POINT,CART,89.7315,113.4024,22.7958,0.0000,0.3915,0.9202
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 89.7315, 114.9671, 26.4734
MEAS/POINT, F(点-10), 1
GOTO/CART, 89.7315,114.9671,66.9967
PTMEAS/CART, 89.7315,113.4024,22.7958,0.0000,0.3915,0.9202
ENDMES
F(点-11)=FEAT/POINT,CART,101.3956,102.0183,27.4257,0.0000,0.4379,0.8990
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 101.3956, 103.7684, 31.0188
MEAS/POINT, F(点-11), 1
GOTO/CART, 101.3956,103.7684,66.9967
PTMEAS/CART, 101.3956,102.0183,27.4257,0.0000,0.4379,0.8990
ENDMES
F(点-12)=FEAT/POINT,CART,116.5215,113.9843,22.5455,0.0000,0.3987,0.9171
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 116.5215, 115.5777, 26.2108
MEAS/POINT, F(点-12), 1
GOTO/CART, 116.5215,115.5777,66.9967
PTMEAS/CART, 116.5215,113.9843,22.5455,0.0000,0.3987,0.9171
ENDMES
F(CIR2)=FEAT/CIRCLE,INNER,CART,8.0000,55.0000,32.0000,0.0000,0.0000,1.0000, 10.0000
F(CIR3)=FEAT/CIRCLE,INNER,CART,24.0000,82.7128,32.0000,-0.0000,-0.0000,1.0000, 10.0000
F(CIR4)=FEAT/CIRCLE,INNER,CART,56.0000,82.7128,32.0000,0.0000,-0.0000,1.0000, 10.0000
F(CIR5)=FEAT/CIRCLE,INNER,CART,72.0000,55.0000,32.0000,0.0000,0.0000,1.0000, 10.0000
F(CIR6)=FEAT/CIRCLE,INNER,CART,56.0000,27.2872,32.0000,-0.0000,-0.0000,1.0000, 10.0000
F(CIR7)=FEAT/CIRCLE,INNER,CART,24.0000,27.2872,32.0000,-0.0000,0.0000,1.0000, 10.0000
F(CIR8)=FEAT/CIRCLE,INNER,CART,40.0000,55.0000,32.0000,0.0000,0.0000,1.0000, 45.0000
F(CIR9)=FEAT/CIRCLE,INNER,CART,40.0000,55.0000,27.0000,0.0000,0.0000,1.0000, 20.0000
F(CIR10)=FEAT/CIRCLE,OUTER,CART,40.0000,55.0000,27.0000,0.0000,0.0000,1.0000, 30.0000
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 8.8760, 55.4890, 66.9967
MEAS/CIRCLE, F(CIR2), 5
GOTO/CART, 8.8760, 55.4890, 66.9967
PTMEAS/CART, 12.3659, 57.4371, 32.0000, -0.8732, -0.4874, 0.0000
PTMEAS/CART, 7.0313, 59.9053, 32.0000, 0.1937, -0.9811, 0.0000
PTMEAS/CART, 3.0355, 55.5946, 32.0000, 0.9929, -0.1189, 0.0000
PTMEAS/CART, 5.9004, 50.4622, 32.0000, 0.4199, 0.9076, -0.0000
PTMEAS/CART, 11.6669, 51.6009, 32.0000, -0.7334, 0.6798, -0.0000
GOTO/CART, 8.7358, 54.3179, 66.9967
ENDMES
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 24.9454, 83.0486, 66.9967
MEAS/CIRCLE, F(CIR3), 5
GOTO/CART, 24.9454, 83.0486, 66.9967
PTMEAS/CART, 28.7116, 84.3864, 32.0000, -0.9423, -0.3347, -0.0000
PTMEAS/CART, 23.8642, 87.7110, 32.0000, 0.0272, -0.9996, -0.0000
PTMEAS/CART, 19.2045, 84.1282, 32.0000, 0.9591, -0.2831, 0.0000
PTMEAS/CART, 21.1720, 78.5894, 32.0000, 0.5656, 0.8247, 0.0000
PTMEAS/CART, 27.0477, 78.7490, 32.0000, -0.6095, 0.7928, -0.0000
GOTO/CART, 24.6115, 81.9174, 66.9967
ENDMES
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 56.8817, 83.1916, 66.9967
MEAS/CIRCLE, F(CIR4), 5
GOTO/CART, 56.8817, 83.1916, 66.9967
PTMEAS/CART, 60.3939, 85.0989, 32.0000, -0.8788, -0.4772, 0.0000
PTMEAS/CART, 55.0885, 87.6290, 32.0000, 0.1823, -0.9832, -0.0000
PTMEAS/CART, 51.0427, 83.3652, 32.0000, 0.9915, -0.1305, -0.0000
PTMEAS/CART, 53.8477, 78.1998, 32.0000, 0.4305, 0.9026, -0.0000
PTMEAS/CART, 59.6271, 79.2712, 32.0000, -0.7254, 0.6883, 0.0000
GOTO/CART, 56.7278, 82.0222, 66.9967
ENDMES
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 72.5942, 55.8084, 66.9967
MEAS/CIRCLE, F(CIR5), 5
GOTO/CART, 72.5942, 55.8084, 66.9967
PTMEAS/CART, 74.9610, 59.0289, 32.0000, -0.5922, -0.8058, 0.0000
PTMEAS/CART, 69.0833, 59.0611, 32.0000, 0.5833, -0.8122, 0.0000
PTMEAS/CART, 67.2363, 53.4810, 32.0000, 0.9527, 0.3038, -0.0000
PTMEAS/CART, 71.9726, 50.0001, 32.0000, 0.0055, 1.0000, -0.0000
PTMEAS/CART, 76.7467, 53.4289, 32.0000, -0.9493, 0.3142, -0.0000
GOTO/CART, 72.9525, 54.6847, 66.9967
ENDMES
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 56.5673, 28.1147, 66.9967
MEAS/CIRCLE, F(CIR6), 5
GOTO/CART, 56.5673, 28.1147, 66.9967
PTMEAS/CART, 58.8270, 31.4113, 32.0000, -0.5654, -0.8248, -0.0000
PTMEAS/CART, 52.9513, 31.2502, 32.0000, 0.6097, -0.7926, -0.0000
PTMEAS/CART, 51.2888, 25.6124, 32.0000, 0.9422, 0.3350, 0.0000
PTMEAS/CART, 56.1370, 22.2891, 32.0000, -0.0274, 0.9996, 0.0000
PTMEAS/CART, 60.7958, 25.8730, 32.0000, -0.9592, 0.2828, -0.0000
GOTO/CART, 56.9623, 27.0034, 66.9967
ENDMES
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 24.7258, 27.9798, 66.9967
MEAS/CIRCLE, F(CIR7), 5
GOTO/CART, 24.7258, 27.9798, 66.9967
PTMEAS/CART, 27.6173, 30.7390, 32.0000, -0.7235, -0.6904, -0.0000
PTMEAS/CART, 21.8349, 31.7941, 32.0000, 0.4330, -0.9014, 0.0000
PTMEAS/CART, 19.0446, 26.6208, 32.0000, 0.9911, 0.1333, 0.0000
PTMEAS/CART, 23.1025, 22.3684, 32.0000, 0.1795, 0.9838, -0.0000
PTMEAS/CART, 28.4007, 24.9136, 32.0000, -0.8801, 0.4747, -0.0000
GOTO/CART, 24.8830, 26.8109, 66.9967
ENDMES
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 54.5076, 66.4848, 66.9967
MEAS/CIRCLE, F(CIR8), 5
GOTO/CART, 54.5076, 66.4848, 66.9967
PTMEAS/CART, 57.6412, 68.9656, 32.0000, -0.7841, -0.6207, 0.0000
GOTO/CART, 50.2485, 70.4058, 32.0000
GOTO/CART, 44.9863, 72.8188, 32.0000
GOTO/CART, 39.2359, 73.4875, 32.0000
PTMEAS/CART, 32.1694, 76.0934, 32.0000, 0.3480, -0.9375, 0.0000
GOTO/CART, 28.5152, 69.5076, 32.0000
GOTO/CART, 24.5942, 65.2485, 32.0000
GOTO/CART, 22.1812, 59.9863, 32.0000
PTMEAS/CART, 17.5192, 54.0709, 32.0000, 0.9991, 0.0413, -0.0000
GOTO/CART, 22.6535, 48.5604, 32.0000
GOTO/CART, 25.4924, 43.5152, 32.0000
GOTO/CART, 29.7515, 39.5942, 32.0000
PTMEAS/CART, 33.9367, 33.3324, 32.0000, 0.2695, 0.9630, -0.0000
GOTO/CART, 40.7641, 36.5125, 32.0000
GOTO/CART, 46.4396, 37.6535, 32.0000
GOTO/CART, 51.4848, 40.4924, 32.0000
PTMEAS/CART, 58.7335, 42.5378, 32.0000, -0.8326, 0.5539, -0.0000
GOTO/CART, 55.4058, 44.7515, 66.9967
ENDMES
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 44.7069, 58.7262, 66.9967
MEAS/CIRCLE, F(CIR9), 5
GOTO/CART, 44.7069, 58.7262, 66.9967
PTMEAS/CART, 47.8405, 61.2069, 27.0000, -0.7841, -0.6207, 0.0000
GOTO/CART, 43.3251, 59.9983, 27.0000
GOTO/CART, 41.6178, 60.7812, 27.0000
GOTO/CART, 39.7521, 60.9982, 27.0000
PTMEAS/CART, 36.5197, 64.3748, 27.0000, 0.3480, -0.9375, 0.0000
GOTO/CART, 36.2738, 59.7069, 27.0000
GOTO/CART, 35.0017, 58.3251, 27.0000
GOTO/CART, 34.2188, 56.6178, 27.0000
PTMEAS/CART, 30.0085, 54.5871, 27.0000, 0.9991, 0.0413, 0.0000
GOTO/CART, 34.3720, 52.9107, 27.0000
GOTO/CART, 35.2931, 51.2738, 27.0000
GOTO/CART, 36.6749, 50.0017, 27.0000
PTMEAS/CART, 37.3052, 45.3699, 27.0000, 0.2695, 0.9630, 0.0000
GOTO/CART, 40.2479, 49.0018, 27.0000
GOTO/CART, 42.0893, 49.3720, 27.0000
GOTO/CART, 43.7262, 50.2931, 27.0000
PTMEAS/CART, 48.3260, 49.4612, 27.0000, -0.8326, 0.5539, 0.0000
GOTO/CART, 44.9983, 51.6749, 66.9967
ENDMES
$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 54.8945, 66.7911, 66.9967
MEAS/CIRCLE, F(CIR10), 5
GOTO/CART, 54.8945, 66.7911, 66.9967
PTMEAS/CART, 51.7608, 64.3104, 27.0000, 0.7841, 0.6207, 0.0000
GOTO/CART, 45.1192, 73.2939, 27.0000
PTMEAS/CART, 34.7796, 69.0623, 27.0000, -0.3480, 0.9375, 0.0000
GOTO/CART, 24.1834, 65.5218, 27.0000
PTMEAS/CART, 25.0128, 54.3806, 27.0000, -0.9991, -0.0413, 0.0000
GOTO/CART, 25.1055, 43.2089, 27.0000
PTMEAS/CART, 35.9578, 40.5549, 27.0000, -0.2695, -0.9630, 0.0000
GOTO/CART, 46.6114, 37.1909, 27.0000
PTMEAS/CART, 52.4890, 46.6919, 27.0000, 0.8326, -0.5539, 0.0000
GOTO/CART, 55.8166, 44.4782, 66.9967
ENDMES
GOTO/55.8934, 44.4504, 209.4494
